Was20160uc Parts

This flexible water hose routes water between internal components in your appliance. Replacing a worn or cracked hose restores a sealed, reliable water path to help prevent leaks and water-flow issues.

• Directs water between assemblies to maintain proper flow
• Helps keep the water path watertight to avoid leaks
• Can resolve symptoms like slow/failed draining, pooling water, or visible drips
• Replaces hoses that are brittle, cracked, kinked, or clogged

• Disconnect power and shut off water supply before servicing
• Place towels or a pan to catch residual water; note original routing
• Move over and secure existing clamps/seals; avoid kinks during routing
• Run a test cycle and check all connections for leaks

This analogue pressure sensor detects water pressure to help the appliance monitor and control water level during cycles, reducing overfill and poor wash performance. It replaces a failed or intermittent pressure-sensing assembly. What it does:

• Senses water/air pressure changes and sends an analogue signal to the control board
• Helps the appliance detect correct water level for fill and drain operations
• Commonly used when the appliance shows water level errors, won't fill properly, or cycles erratically
• Can resolve intermittent or no-signal conditions caused by a faulty sensor

• One analogue pressure sensor

• Disconnect power (and water, if applicable) before inspection or replacement
• Handle the sensor and its connector carefully to avoid damage to terminals or diaphragm
• Verify hose and fittings to the sensor are clean and free of kinks or blockages

This flexible inlet/fill hose routes water into the appliance, restoring proper water delivery for normal operation. Replace a damaged hose to stop leaks and ensure reliable water flow. What it does:

• Carries incoming water from the supply to the appliance fill assembly
• Prevents water leaks when intact; a cracked or split hose can cause pooling or drips
• Restores normal fill behavior when worn or collapsed hoses reduce flow
• Works with clamps or fittings at each end to create a watertight seal

• One flexible inlet/fill hose

• Turn off the water supply and disconnect power before removing the old hose
• Inspect and replace any worn clamps, gaskets, or fittings for a secure seal
• Hand-start fittings, then tighten with tools—avoid over-tightening to prevent damage
• After installation, restore water and power, then run a short cycle and check for leaks

This door lock assembly secures the appliance door during operation so cycles can run safely and reliably. It replaces a worn or broken latch to restore proper door closure and locking action. What it does:

• Secures and latches the appliance door so the unit can start and run
• Prevents the door from opening mid-cycle, reducing leaks and interruptions
• Common fix for door-not-locking, door won't stay closed, or related error codes
• Works as the mechanical/electrical interface that detects a closed door

• Disconnect power before beginning any repair to avoid shock
• Handle carefully; avoid forcing the latch or twisting mounting tabs
• Verify correct orientation and engage mounting screws securely but not overtighten

This Frame-Window is the outer trim for a appliance door window, restoring the door's finished appearance and protecting the inner glass. Replaces damaged or worn door frame trim to improve seal appearance and safety. What it does

• Holds and trims the door window assembly, keeping the inner glass secured and protected.
• Restores the door's finished look when the original frame is cracked, warped, or cosmetically damaged.
• Helps maintain a proper window fit so the glass stays in place during normal use.
• Reduces drafts and visible gaps caused by a broken or missing outer frame.

• One Frame-Window outer door frame (single piece as shown)

• High-level replacement: remove the door or open per appliance instructions before disassembly; follow OEM guidance.
• Handle glass and trim carefully; wear cut-resistant gloves and eye protection.
• Keep fasteners and glass pieces secure during reassembly; verify a proper fit before normal use.

This frame window is the trim piece that surrounds the dishwasher door's viewing window, restoring the door's appearance and helping keep the window secure. It replaces cracked, warped, or damaged trim for a finished look. What it does:

• Replaces damaged or cracked door window trim to restore appearance
• Secures the window assembly and helps maintain proper fit in the door
• Stops drafts and reduces the chance of water reaching the inner door cavity when the trim is intact
• Addresses cosmetic damage and rattling caused by loose or broken trim

• Disconnect power to the appliance before beginning any repair
• Handle glass and trim edges carefully to avoid cuts or breakage
• Installation typically requires removal of the outer door panel and fasteners; keep track of hardware

This replacement fixture assembly secures internal components and restores proper alignment and fit in compatible appliances. Replacing a worn or damaged fixture helps stop noise, prevent rubbing, and maintain safe operation. What it does:

• Holds adjacent parts in the correct position to prevent movement and misalignment
• Reduces rattling, vibration, or scraping noises caused by loose or broken supports
• Helps maintain door/panel fit and seals where applicable
• Restores the original mounting function to prevent further wear on connected components

• Disconnect power and water before beginning any repair
• Use basic hand tools; follow service manual or tech sheet for exact disassembly steps
• Handle carefully to avoid damaging surrounding trim, wiring, or seals