Was24460uc Parts

This lower dispenser tray fits inside the dishwasher detergent dispenser and provides a stable catch and guide for detergent and rinse aid, helping the dispenser operate cleanly and reliably. Replaces a cracked or warped tray to reduce leaks and residue buildup. What it does:

• Holds and positions the lower portion of the detergent/dispenser assembly for proper door sealing and release
• Directs detergent and rinse aid into the wash chamber when the dispenser opens
• Helps prevent leaks and pooling that can cause poor detergent release or residue
• Restores proper alignment if the original tray is cracked, broken, or deformed

• Disconnect power to the appliance before starting any repair
• Remove the dishwasher door inner panel or dispenser bezel as required to access the dispenser assembly
• Handle parts gently to avoid damaging clips and seals; replace any worn gaskets

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten

Replacement holder that secures internal components and accessories, restoring proper fit and preventing movement or rattling. Direct-fit design replaces a worn, cracked or broken holder to keep parts stable during normal operation. What it does

• Secures panels, racks or small internal components in place to prevent shifting.
• Restores correct alignment when a broken holder allows parts to sag or detach.
• Eliminates rattling or vibration caused by loose or damaged mounts.
• Helps maintain proper operation by keeping components positioned as intended.

• Disconnect power (and water supply if applicable) before starting repair.
• Remove any obstructing panels or accessories to access the holder; keep track of fasteners.
• Install the new holder in the same orientation; snap or fasten it until it seats securely—do not force or overtighten.

This analogue pressure sensor detects water pressure to help the appliance monitor and control water level during cycles, reducing overfill and poor wash performance. It replaces a failed or intermittent pressure-sensing assembly. What it does:

• Senses water/air pressure changes and sends an analogue signal to the control board
• Helps the appliance detect correct water level for fill and drain operations
• Commonly used when the appliance shows water level errors, won't fill properly, or cycles erratically
• Can resolve intermittent or no-signal conditions caused by a faulty sensor

• One analogue pressure sensor

• Disconnect power (and water, if applicable) before inspection or replacement
• Handle the sensor and its connector carefully to avoid damage to terminals or diaphragm
• Verify hose and fittings to the sensor are clean and free of kinks or blockages

This replacement dispenser tray fits the detergent cup assembly to hold and release dishwasher detergent for normal wash cycles. Restores proper detergent containment and helps ensure detergent is delivered during the wash. What it does

• Holds powdered or tablet detergent in the machine's dispenser area
• Allows detergent to be released at the correct time during the wash cycle
• Replaces cracked, warped, or missing trays that cause leaking or improper release
• Helps prevent detergent from dissolving too early or pooling inside the dispenser

• One dispenser tray

• Disconnect power (and water, if applicable) before servicing for safety
• Remove the old dispenser by opening the door and releasing the dispenser latch; install the new tray by aligning and snapping into place
• Check the dispenser cover and latch operation after installation to ensure proper release

This pressure-chamber hose routes the dishwasher's tub pressure signal to the water-level chamber so the control can detect fill level and stop filling when appropriate. It helps restore proper fill control and reliable cycle operation. What it does:

• Carries air/water pressure from the tub to the pressure chamber for accurate water-level sensing
• Enables the dishwasher to detect full/overfill conditions and stop the fill valve
• Can prevent overfilling, continuous filling, or erratic cycle behavior when functioning
• Failures may cause fill errors, long fill times, or incorrect cycle operation

• One pressure chamber hose (single replacement hose as shown)

• Disconnect power and water supply before servicing the dishwasher
• Access may require removing lower kickplate and/or tub access panels per your model service instructions
• Inspect hose routing and clamps; replace any damaged clips and ensure hose is free of kinks when installing