Wce55usohb01 Parts

Replacement control knob that restores simple, reliable user control of appliance settings. Installs quickly to replace a cracked, worn or missing knob so you can accurately select heat or function positions. What it does:

• Provides the user interface to turn and set appliance controls (temperature, power or function)
• Replaces damaged or missing knobs that make settings hard to choose or read
• Slides onto the factory control shaft for a secure fit and positive detents
• Restores tactile grip and clear setting selection for safe operation

• Disconnect electrical power (and shut off gas supply where applicable) before servicing.
• Remove the old knob by pulling it straight off the control shaft; align the replacement and push it fully onto the shaft until seated.
• No special tools are usually required; if a set screw is present, tighten gently—do not overtighten.
• Reconnect power/gas and test control function after installation.

This replacement Thermostat Fix repair kit secures the thermostat assembly to help stabilize temperature sensing and restore consistent appliance performance. It's a small service part used when the thermostat mounting or retention hardware is worn or damaged. What it does

• Secures or replaces thermostat mounting/retention hardware to keep the sensor in proper contact
• Helps reduce intermittent temperature readings or cycling caused by a loose thermostat
• Restores stable thermostat positioning after vibration or wear
• Can stop noise or rattling related to a loose thermostat assembly

• One Thermostat Fix repair part

• Disconnect power to the appliance before servicing to prevent shock or injury
• Access the thermostat area per your appliance's service instructions; retain any screws or clips removed
• Replace the worn or damaged retention piece with this part and verify secure fit before reassembly

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

The Cooktop is an OEM replacement part for Whirlpool cooktops. It is responsible for providing the heating surface and burners that allow for versatile cooking. 

The cooktop is subject to heat, spills, and regular wear that can cause deterioration over time. Causes of a bad cooktop can include cracks or damage in the glass or ceramic top, burned or non-functional heating elements, or issues with the control panel or electronic components.   

Symptoms of a bad cooktop include:

• Slow or uneven heating of burners
• Burners that will not ignite or turn off unexpectedly  
• Discoloration or cracks in the glass or ceramic surface
• Leaks or loose fittings on the control valves

This Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This genuine replacement screw secures appliance components so panels, brackets, and assemblies stay tight and properly aligned. Replacing stripped, rusted, or missing hardware restores a solid fit and helps prevent rattles, shifting, or looseness over time.

• Fastens panels, brackets, and internal parts to maintain proper alignment
• Helps resolve issues caused by missing or damaged screws
• Restores secure mounting after service where original hardware is lost
• Use when threads are stripped or the screw head is damaged and won't tighten

• Disconnect power; turn off gas supply if applicable before servicing
• Match screw location and length to your model's parts diagram for correct placement
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent damage to mounting points

This hardware kit contains the small mounting parts needed to secure and support the appliance component. It provides replacement fasteners and brackets to restore proper fit and stability after service. What it does:

• Replaces worn or missing mounting pieces that cause loose panels or components
• Restores proper alignment and support for the associated assembly
• Helps stop rattling, vibration, or movement caused by missing hardware
• Matches OEM fit and function when used as a direct replacement

• Intended for technicians or experienced DIYers; inspect the kit before installation
• Use appropriate hand tools; tighten fasteners to manufacturer torque where specified
• Disconnect power and follow all safety procedures before servicing the appliance
• Replace only the parts shown for your specific model

This replacement control knob restores a solid, precise feel when selecting settings on your appliance. It replaces a cracked, loose, or missing knob so the control shaft engages properly and your chosen settings hold. What it does:

• Mounts on the control shaft to select functions such as cycles, temperature, or burner level
• Common symptoms: cracked/broken knob, loose or wobbly fit, knob falls off, turns without engaging the control
• Restores proper engagement so settings stay put during use
• Direct replacement sized to fit the original control shaft interface

• Includes 1 control knob

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—avoid prying against the control panel
• Align the new knob with the shaft and press firmly until fully seated
• After installation, rotate through settings to ensure proper engagement

This top surface cooktop is the factory-style replacement part that restores a safe, level cooking surface and the correct mounting for burners and controls. It renews appearance and function after damage or wear. What it does:

• Replaces a cracked, chipped, warped or heavily scratched cooktop surface to restore a stable area for cookware.
• Provides the proper mounting and alignment for burners, grates and control components.
• Helps prevent heat and moisture from reaching internal components when sealed correctly.
• Addresses symptoms such as uneven burner seating, visible surface damage, and cosmetic deterioration.

• Disconnect electrical power (and gas supply if applicable) before starting any repair.
• Handle glass or finished surfaces carefully; use gloves and a soft support to avoid breakage or scratches.
• Keep all original mounting hardware and gaskets; verify whether additional clips or screws are required for your model.

The Cooktop is an OEM part for Whirlpool cooktops. It provides the vital flat or grates surface needed for cooking and preparing meals. The cooktop contains the multiple electric cooking elements or gas burners required for heating pots, pans and other cookware.

Causes of a damaged cooktop can be excess temperature fluctuations, improper cleaning techniques, damage from heavy pots and pans, or normal wear over extended use.

Symptoms of a bad cooktop include:

• Elements or burners that do not heat properly or inconsistently
• Hot spots or cold spots on the cooktop surface
• Visible wear and distortion of the glass or metal cooktop
• Dents, cracks or other physical damage

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This selector switch is the user-control switch that lets the appliance choose functions or cycles. It replaces a worn or failed control selector to restore reliable selection of settings and cycles. What it does:

• Routes user input to the appliance control so chosen settings engage correctly
• Enables selection between cycles, temperatures, or functions depending on appliance design
• Commonly replaced when selector turns freely, feels loose, or selections do not register
• Helps stop intermittent or no-response behavior from the control panel related to the selector

• Disconnect power to the appliance before beginning any repair to avoid shock.
• Access may require removing control panel or console; keep screws and small parts organized.
• Handle the switch and wiring gently; avoid pulling on wires—use proper disconnect tools.
• After installation, restore power and verify all selector positions function before reassembling fully.

This genuine rubber grommet cushions and secures components where wiring, hoses or metal parts pass through panels to prevent rubbing and reduce vibration. It restores proper fit and helps stop wear that can lead to noise or chafing. What it does:

• Cushions and isolates parts to reduce vibration and rattling
• Protects wiring and hoses from abrasion where they pass through holes
• Holds panels or components in position for a correct fit
• Helps eliminate intermittent noises caused by loose or worn mounts

• Disconnect power to the appliance before beginning any service
• Inspect surrounding area for damage; replace any frayed wires or cracked panels
• Typically presses into place by hand; use a non-marring tool if needed to avoid tearing
• If grommet fits tightly, apply a small amount of mild soap or lubricant for installation — avoid petroleum-based products on rubber