Wd21x10215 Parts

Base bracket that holds the leveling foot at the washer cabinet. Replace if cracked, broken, or missing to restore stability and prevent rocking or vibration.

This plastic connector joins the drain hose between a washer pedestal and the main washer unit. It provides a secure, leak-free connection so water can flow properly from the pedestal through the drain system. Replace this connector if you notice water leaking at the hose junction or if the fitting is cracked or damaged.

Dryer door hinge provides the pivot point for smooth opening and closing. Replace if hinge is cracked, broken, worn from repeated use, or missing.

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

Secures hose connections to maintain watertight seals in your washer. Replace if you notice leaks or loose hoses during operation. Verify fit with model number.

Secures the leveling foot to the washer base. Replace if cracked, stripped, or missing to restore a solid mounting point for proper leveling and stability.

Fix standing water in your washer tub with a new drain pump assembly. Restores proper water removal during drain and spin cycles to complete loads.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Dryer drum baffle lifts and tumbles clothes while circulating air evenly. Replace if cracked, loose, or causing noise. Verify fit with your model number.

This is the inner frame that fits inside the dryer door, providing structural support and holding the door components in place. It forms the interior-facing portion of the door assembly and helps maintain a proper seal during operation. Replace this frame if it is cracked, warped, or broken, which can cause the door to not close properly or allow heat to escape during drying cycles.

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

Detergent not dispensing or leaking during wash? This dispenser assembly routes detergent into the drum and stops leaks. Restores reliable dispensing.

Fix a dryer making loud noises or not tumbling with a new drum. This part holds clothes during the drying cycle and may rust, dent, or crack over time.

Dryer won't start or door won't stay closed? This door latch assembly secures the door during operation, allowing cycles to run. Moderate DIY repair.

This is a door lock and switch assembly that secures the washer door during operation and signals the control board that the door is properly closed. It prevents the door from being opened while the drum is spinning and allows the wash cycle to begin. Replace this assembly if the washer won't start, displays a door lock error code, the door won't lock or unlock, or the cycle stops unexpectedly.