Wdf320padw Parts

This float assembly sits in the dishwasher tub and rises with incoming water to signal the float switch to stop filling. Replacing a worn or sticking overfill protector restores proper water level control and helps prevent overfilling and leaks.

• Monitors water level by floating upward as the tub fills
• Triggers the float switch to shut off the inlet valve at the correct level
• Helps prevent overfilling and potential leaks
• Helps with: won't fill or stops filling early, water level too high, float sticks or is visibly damaged

• Disconnect power and shut off the water supply before servicing.
• Remove the lower rack to access the float inside the tub.
• Lift the old float straight up; on some models a retainer under the tub must be released to remove it.
• Transfer any existing hardware if needed, install the new float, ensure free movement, then restore power and test for proper fill.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This dishwasher circulation pump and motor drives wash water through the spray arms for effective cleaning. Replacing a failed wash motor restores strong spray pressure and consistent cleaning performance throughout the cycle.

• Circulates water through the spray arms to wash and rinse dishes
• Maintains proper flow and pressure from the sump to all spray arms
• Direct replacement for a seized, noisy, or non-running wash motor
• Common symptoms: poor cleaning, no spray action, or humming/buzzing during wash

• Disconnect power at the breaker and shut off water supply before servicing.
• Access is from the bottom/front; many models require removing the toe panel and/or sliding the dishwasher out.
• Connect the wiring, seat the pump seal fully in the sump, and lock the assembly in place per your model's procedure.
• After reassembly, run a brief fill-and-wash to check for leaks and proper spray action.

This Electronic Control Board is the appliance's main control module. It interprets user inputs and manages cycle timing and power to components, restoring normal operation when a failed board causes no power, no start, or erratic behavior.

• Serves as the central "brain," processing inputs and controlling key functions
• Directs power to motors, pumps, valves, fans, and heaters as programmed
• Oversees cycle timing and monitors sensors/switches for proper operation
• Failure symptoms include dead display/no power, won't start, unresponsive buttons, random resets, or error codes

• Disconnect power to the appliance before servicing.
• Use ESD protection and handle the board by the edges.
• Photograph connectors; transfer any jumpers or mounting clips from the original board.
• After installation, restore power and run diagnostics or calibration if required.

Color: Stainless

The Control Board is an OEM replacement part for Whirlpool dishwashers. It is responsible for controlling and coordinating the various functions and settings of the dishwasher.

A bad control board can occur due to electrical issues, component failure, or damage to the board itself. If you notice symptoms such as the dishwasher not starting or responding to commands, erratic operation, or error codes displayed on the control panel, it may indicate a faulty control board.

Symptoms of a bad control board include:

• Dishwasher not starting or responding to commands
• Erratic operation
• Error codes displayed on the control panel

Restore your dishwasher by replacing the faulty or damaged control board with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Color: Black
 

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This inner vent gasket seals the dryer vent opening to direct hot air through the exhaust system and help maintain proper airflow. Replacing a worn or torn vent gasket restores a tighter seal and reduces air leaks. What it does:

• Seals the inner vent area to keep exhaust air flowing through the ductwork.
• Helps prevent air leaks that can cause longer dry times or uneven drying.
• Reduces lint escape and buildup around the vent opening.
• Restores proper airflow to help the dryer run more efficiently.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing panels or the drum—follow your model's service instructions.
• Inspect the mounting surface for damage or debris and clean before installing the new gasket.
• Ensure the gasket is seated evenly and not pinched during reassembly; test operation after installation.

This inner door panel replaces the appliance's damaged interior door surface to restore proper fit, protect internal components, and improve appearance. It also restores structural support and helps keep insulation and inner glass secure for reliable operation. What it does:

• Replaces the door's interior panel that supports inner glass, insulation, and internal hardware.
• Protects wiring, controls, and insulation inside the door from damage and moisture.
• Addresses common symptoms like cracked or dented inner panels, rattling or loose-feeling doors, and visible gaps between door layers.
• Restores proper door fit and interior appearance after impact or wear.

• Disconnect power (and water supply if applicable) before starting work.
• Wear cut-resistant gloves and handle any glass or sharp edges carefully.
• Retain and reuse original fasteners when possible; align the panel before fully tightening screws.

This dispenser cover is the replacement lid for a washer dispenser assembly, restoring a secure, functional cover that keeps detergent and fabric softener contained until the wash cycle. It helps prevent spills and keeps the dispenser looking finished. What it does:

• Replaces a cracked, warped, or missing dispenser lid so the dispenser closes properly
• Helps contain detergent and softener to prevent drips and spills onto the washer top
• Restores a flush, finished appearance to the dispenser area
• Works with the dispenser housing to ensure proper release of cleaning agents during cycles

• Disconnect power and water supply before servicing the washer
• Replacement typically installs with clips or screws; keep original fasteners and note their placement
• Handle plastic parts carefully to avoid cracking; align tabs before snapping into place

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

This wire harness is an OEM-style electrical connector assembly that routes power and signals between the control and appliance components, restoring reliable connections and helping resolve intermittent or failed operation. What it does:

• Replaces damaged, frayed or corroded wiring that can cause intermittent power or communication failures
• Restores proper connections between controls, motors, sensors or switches
• Helps stop issues like failure to start, erratic operation, or components not responding
• Provides factory-style plug-and-play connectors for a secure fit

• Disconnect power to the appliance before beginning any repair
• Compare the new harness to the old one to ensure connector locations and length before installation
• Route and secure the harness away from moving parts and heat sources to prevent wear
• If you find burned connectors or other damage, inspect related components and wiring for root causes