Wdf580afm2 Parts

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

This passive vent assembly allows moist air to escape during the dry cycle, helping reduce steam and moisture inside the dishwasher tub. Replacing a warped or leaking vent can improve drying performance and prevent moisture from seeping onto the door panel.

• Allows steam to vent from the tub without a fan
• Helps reduce condensation and moisture buildup during drying
• Common fix for visible steam leaks at the door, moisture on the console, or poor drying results
• Restores proper air path through the door vent channel

• Disconnect power and shut off water supply before servicing
• Access is typically from the inner door; remove the inner panel to reach the vent
• Inspect and replace any damaged gasket or door insulation as needed
• Ensure the vent seats evenly and fasteners are snug to prevent leaks

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

This pump and motor assembly has been manufactured by Whirlpool for use with compatible dishwasher models. The pump is responsible for pumping water through the dishwasher's spray arms, while the motor drives the pump. Either of these parts could be faulty if the user notices that the dishes are coming out dirty after the cycle is over, or the motor is making an excessively loud sound, the pump and motor may need replaced. This assembly includes all parts necessary for replacing both the pump and motor.This is a genuine OEM part and has been sourced directly from the manufacturer. This pump and motor assembly is compatible with different dishwashers manufactured by Whirlpool, Maytag, Jenn-Air, Amana, and other brands.

12 Ft in length

Includes two screws, two clamps, and undercounter mounting brackets.

This electronic control board is the appliance's main control (PCB) that coordinates programmed functions and powers key components. Replacing a failed board restores accurate cycle timing and responsive controls for reliable, consistent operation. What it does

• Manages the timing and sequencing of appliance operations
• Interprets inputs from the user interface, sensors, and switches
• Controls power to loads such as motors, valves, heaters, and fans
• Common symptoms of failure: won't start or complete a cycle, unresponsive or erratic controls/display, error codes/alarms, or intermittent operation

• 1 electronic control board

• Disconnect power (unplug or switch off the circuit breaker) before servicing
• Use ESD protection and handle the board by its edges to avoid static damage
• Note/photograph wire locations; transfer connectors one at a time and seat them fully
• Run diagnostics/self-test after installation if available

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Color: Grey

Located between the console and door

This overfill protector housing mounts in the dishwasher tub floor to guide the overfill float and position the switch actuator. Replacing a damaged housing helps stop leaks at the float opening and restores proper overfill protection.

• Guides the overfill float at the tub floor so it moves freely
• Allows the float to engage the overfill switch and stop water fill at high level
• Restores proper fit if the original housing is cracked, warped, or missing
• Typical symptoms include leaking near the float, overfilling, or inconsistent fill levels

• Disconnect power and shut off water supply before servicing
• Remove the toe panel and lower rack to access the float area
• You may need to lift out the float and remove the under-tub switch bracket to replace the housing; note part orientation
• After reassembly, run a brief fill and check for leaks at the float opening

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This electronic control board is the appliance's central controller, interpreting user inputs and managing power to key components. Replacing a failed board restores responsive controls, proper cycle execution, and reliable overall operation. What it does:

• Interprets keypad or selector inputs and executes programmed functions
• Switches relays to power motors, valves, heaters, and other loads as required
• Drives the display and status indicators; stores and shows diagnostic/error codes
• Monitors sensor inputs to protect the appliance and maintain correct operation
• Common failure symptoms include a blank or unresponsive display, inability to start cycles, erratic operation, or error codes traced to the control

• 1 electronic control board

• Disconnect power to the appliance before servicing; follow all safety precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to match original locations
• Some models require a service/diagnostic or configuration step after installation; refer to the unit's tech sheet or service guide

This dishwasher rinse aid dispenser knob mounts on the inner-door dispenser and lets you set the rinse-aid dosage. Replace a cracked, stripped, or missing knob to restore easy adjustment and consistent rinse-aid use during the rinse/dry cycle.

• Adjusts the rinse-aid dispensing level on the dispenser
• Restores a secure, readable setting pointer for dosage control
• Common symptoms: knob broken or missing, won't stay on, can't turn or adjust settings, stripped splines
• Helps address inconsistent rinse-aid use when the setting can't be changed

• Disconnect power to the dishwasher before servicing
• Open the door; pull the old knob straight off (gently pry evenly if needed to avoid damage)
• Align the new knob with the flat/splines and press on; it turns through the full setting range
• On some models, accessing retainers may require removing inner-door screws—refer to your service information

Used on the upper dishwasher dishrack.