Wdp86802 Parts

This lower wiring harness assembly routes power and signals to the appliance's lower components, restoring proper electrical connections so the unit can operate reliably. It's a direct-replacement harness used where factory wiring was damaged or disconnected. What it does:

• Replaces the lower cabinet wiring that connects switches, sensors and motor/valve circuits
• Restores power and signal paths that can cause intermittent operation or failure to run
• Helps eliminate loose, frayed or broken wire connections that create electrical faults
• Supports safe, correct routing and connector fit for reliable component function

• One lower wiring harness assembly as shown

• Disconnect power (unplug or shut off breaker) before starting any work
• Take a photo of the original wiring and connector positions to ensure correct reassembly
• Route the harness exactly as OEM; avoid pinching or sharp edges and secure with existing clips/fasteners

The Clip is an OEM part for Whirlpool dishwashers. It securely attaches the drain hose in place, directing wastewater out of the dishwasher during drain cycles.

Causes of a bad clip can be cracks, breaks, or deformations causing weakened grip. Normal wear and repeated drain cycles can also damage the clip over time.

Symptoms of a bad drain hose clip include:

• Water or leaks around the base of the dishwasher
• Puddles forming due to the hose slipping out of place
• Improper drainage if the hose is not positioned correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dishwasher Track/Support is an OEM component specifically designed for Whirlpool dishwashers. It anchors underneath the dish rack and slides upon which it rolls. 

Causes of a faulty track/support can include cracks, deformities or other damage accumulating from years of bearing weight.

Symptoms of a bad track/support include: 

• Dishes failing to properly secure inside wash rack
• Rack sliding out of position unintentionally  
• Noisy vibrations or shaking heard from below

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

The Wire Harness Assembly is an OEM component for Whirlpool dishwashers. It is the main electrical wiring component that connects and transmits power between various areas and modules inside the dishwasher. 

Causes of a bad wire harness can include cracked, frayed, or damaged insulation over wiring due to normal movement and vibration during the wash cycle. 

Symptoms of a bad wire harness assembly include:

• Lights or elements failing to power on as expected  
• Control panel malfunctions or unintended switches in operation modes
• The entire dishwasher ceasing to function

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

Color: Black
 

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Number-8, 18-thread screw used to secure panels, brackets and small assemblies in Whirlpool appliances. Replacing a missing or damaged screw restores secure mounting and helps stop rattling or loose parts. What it does:

• Fastens trim, panels, brackets or small appliance components that use a #8-18 threaded fastener
• Restores secure mounting when a screw is lost, stripped or damaged
• Helps eliminate vibration-related noise from loose parts
• Simple replacement part for basic fastening needs

• Disconnect power to the appliance before servicing and work on a cool, stable surface
• Use the correct screwdriver or driver bit to avoid cam-out or stripped heads
• Thread in straight and tighten until snug; do not over-torque to avoid stripping threads or damaging components
• Replace with the identical screw type and size for proper fit and function

This inner vent gasket seals the dryer vent opening to direct hot air through the exhaust system and help maintain proper airflow. Replacing a worn or torn vent gasket restores a tighter seal and reduces air leaks. What it does:

• Seals the inner vent area to keep exhaust air flowing through the ductwork.
• Helps prevent air leaks that can cause longer dry times or uneven drying.
• Reduces lint escape and buildup around the vent opening.
• Restores proper airflow to help the dryer run more efficiently.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing panels or the drum—follow your model's service instructions.
• Inspect the mounting surface for damage or debris and clean before installing the new gasket.
• Ensure the gasket is seated evenly and not pinched during reassembly; test operation after installation.

This inner door panel replaces the appliance's damaged interior door surface to restore proper fit, protect internal components, and improve appearance. It also restores structural support and helps keep insulation and inner glass secure for reliable operation. What it does:

• Replaces the door's interior panel that supports inner glass, insulation, and internal hardware.
• Protects wiring, controls, and insulation inside the door from damage and moisture.
• Addresses common symptoms like cracked or dented inner panels, rattling or loose-feeling doors, and visible gaps between door layers.
• Restores proper door fit and interior appearance after impact or wear.

• Disconnect power (and water supply if applicable) before starting work.
• Wear cut-resistant gloves and handle any glass or sharp edges carefully.
• Retain and reuse original fasteners when possible; align the panel before fully tightening screws.

This dispenser cover is the replacement lid for a washer dispenser assembly, restoring a secure, functional cover that keeps detergent and fabric softener contained until the wash cycle. It helps prevent spills and keeps the dispenser looking finished. What it does:

• Replaces a cracked, warped, or missing dispenser lid so the dispenser closes properly
• Helps contain detergent and softener to prevent drips and spills onto the washer top
• Restores a flush, finished appearance to the dispenser area
• Works with the dispenser housing to ensure proper release of cleaning agents during cycles

• Disconnect power and water supply before servicing the washer
• Replacement typically installs with clips or screws; keep original fasteners and note their placement
• Handle plastic parts carefully to avoid cracking; align tabs before snapping into place

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

This stainless steel fine filter traps food particles in the dishwasher sump to help keep wash water cleaner and improve cleaning performance. Durable, corrosion-resistant construction fits the factory filter location. What it does:

• Captures small food debris to prevent recirculation and redepositing on dishes
• Helps maintain proper water flow through the wash system
• Reduces the risk of clogs in the dishwasher pump and spray arms
• Supports consistent cleaning results when the filter is clean and installed correctly

• One stainless steel fine filter

• Disconnect power to the appliance before servicing
• Remove the lower rack and locate the sump area to access the filter
• Clean surrounding area of heavy debris before installing the new filter
• Reinstall securely and run a short cycle to confirm normal operation

This adjuster secures and levels the appliance cabinet to keep it stable and reduce rocking during use. It replaces a worn or damaged leveling adjuster to restore proper machine balance and help prevent vibration-related noise. What it does:

• Provides adjustable support under the appliance to correct uneven floors
• Helps stabilize the cabinet to reduce rocking, vibration, and movement
• Restores correct clearance for doors/panels that bind due to uneven leveling
• Commonly replaced when an existing adjuster is stripped, broken, or missing

• Turn off and unplug the appliance before attempting any service
• Raise the appliance slightly with appropriate support to access the adjuster; use shims or jack stands for safety
• Thread the new adjuster in or out until the appliance sits level, then test stability before removing supports

This adjuster is the height-adjustable leveling leg that helps stabilize and level your appliance for quieter, more even operation. It restores proper balance to reduce rocking, vibration, and uneven wear. What it does:

• Raises or lowers one corner to level the appliance and improve stability
• Helps stop rocking and excessive vibration during operation
• Promotes even load distribution to reduce noise and wear
• Can correct uneven gaps between the appliance and the floor

• Disconnect power and water before servicing; follow all safety steps in your owner's manual
• Support the appliance securely before removing or adjusting legs to prevent tipping
• Turn or thread the adjuster in small increments until the appliance is level; check with a spirit level
• Use common hand tools as needed; enlist a helper for heavy appliances

Size: 8-32 x 1/2 inch.