We11x20397 Parts

This is a starter solenoid used in a variety of riding lawn mowers and yard tractors. Unlike most push mowers that are started by pulling a rope and firing a magneto, riding mowers have starters and batteries. The solenoid is the link between the battery and starter. When the ignition key is turned, electricity from the starter flows through the solenoid to the mower's ignition, firing the engine. Because it is the part subjected to abrupt electrical charges, over time the solenoid's internal workings may fail and the device must be replaced. A symptom of a bad solenoid is the if the engine fails to turn over. To make sure the problem is not the battery, turn the ignition switch on and use a screwdriver to simultaneously touch both terminals of the solenoid. If the engine turns over, the solenoid must be replaced. The solenoid sits inside the engine housing by the starter motor. Before starting to replace it, disconnect the positive battery cable. Replacing this device is as simple as disconnecting the wires that attach it to the battery and unbolting it from the engine housing. This solenoid is a genuine OEM replacement part that is manufactured to be an exact replacement for the original part. This solenoid is compatible with Poulan, Husqvarna, Craftsman, and Weed Eater equipment.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

This hub cap is manufactured by Husqvarna and comes in glossy black color. The main function of a hub cap is to provide a protective barrier or cover for the wheel hub and lug nuts against dirt, grime, and other harmful elements. Wheels that do not have hub caps are more susceptible to damage. Corrosion or rust on the lug nuts is common for wheels free of hubcaps. This results in harder lug nut removal. Over time, rust can spread and damage the hub. With hub caps installed, costly repairs and replacements are no longer a concern. Installing a hub cap will take less than five minutes. A rubber ballet can be used to push the hub cap to the wheel hub. To install this genuine front hub cap, simply push it down or use a rubber mallet. When protecting the hub and axle of a lawnmower, this Husqvarna 532104757 Front Axle Hub Cap OEM replacement is an option. It is an OEM front axle hub cap compatible with most Husqvarna Weed Eater, Poulan and Craftsman tractor and mower models. This front axle hub cap is sold individually.

This headlight switch is a genuine Husqvarna part, sold individually. This headlight switch can be used as a replacement part in a lawnmower. The purpose of the headlight switch in a lawnmower is to provide the operator with a source of illumination in order to operate the appliance at any point during the night or during a period of sustained darkness.The headlight switch in a lawnmower might have to be completely replaced if it can no longer trigger the turning on of the headlights of the appliance when the operator desires to use the appliance in darkness. The headlight switch could suffer damage due to exposure to inclement weather, general wear and tear over long-term use, or an accidental collision with a hard object.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This headlight switch is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Ariens, Poulan, Murray, and Dixon.

This genuine Husqvarna part is a hairpin cotter intended for use with Poulan, Husqvarna and Weed Eater brand walk-behind lawn mowers. This hairpin cotter, also known as a clip or hinchpin, is used to secure a component on a shaft in the lawn mower . This part is shaped like a bobby pin with a single piece of metal formed into a large ring at the top end, and a "W" shape at the other. This is designed to work with the groove or hole at the tip of a hitch pin, where this pin will lock larger pins in place. This part is an identical replacement for an original carrier bracket that is damaged, faulty, or missing. This dependable bracket carrier is made of high quality durable metal.This is an OEM replacement part sourced directly from the manufacturer and is sold individually. For installation information or hardware requirements, please refer to the original product manual. This part is a suitable replacement for a hairpin cotter in products from Husqvarna, Poulan, Weed Eater, Craftsman, Murray, Ariens, Ryobi, and other brands.

This height adjuster knob is for lawn mowers. It attaches to the mower's height adjuster lever to adjust the lawn mower deck to the desired cutting height. Adjusting the lawn mower height ensures that the lawn is cut to the proper mowing height. The correct mowing height for a lawn depends on multiple factors, such as the type of grass species and the time of year. Height adjuster levers are typically made of metal, so the slightly rubberized height adjuster knob protects the operator during the adjustment process. The height adjuster knob's flat surface also prevents slippage during the adjustment process. The knob slides onto the lever and attaches without any clips, retainers, or screws. To remove the knob, pull it off. It might be challenging to remove. Due to the location of the height adjuster knob, wearing gloves is recommended when replacing the knob. This knob is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with lawn mowers made by Craftsman, Husqvarna, Weed Eater, Poulan, and Murray.

This tire is a genuine Husqvarna part, sold individually. This tire can be used as a replacement part for a lawn mower or a lawn tractor.The tire for a lawn mower or a lawn tractor might eventually have to be replaced if it shows signs of damages that cannot be fixed by a basic repair. If the tire has been damaged, it should be removed and replaced with this genuine OEM replacement part before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This tire is compatible with the following outdoor appliance brands: Husqvarna, Poulan, Weed Eater, and Craftsman.

This shoulder bolt is a genuine Husqvarna part, sold individually. This shoulder bolt can be used as a replacement part or a string trimmer. The purpose of a shoulder bolt is to serve as a fastening component of a lawn mower or a string trimmer in conjunction with a nut, so several components within the infrastructure of the appliance are held together and secured in place.The shoulder bolt might be easily lost or misplaced or could be damaged over time. If the shoulder bolt is stripped, the component should be replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This shoulder bolt is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Ariens.

This ignition switch kit is a genuine MTD part, sold individually. This ignition switch kit can be used as a replacement part in a lawnmower. The purpose of the ignition switch kit in a lawnmower is to provide all of the necessary components and fasteners required to replace an ignition switch, which is used to power on the engine and operate the lawnmower across a variety of surfaces.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This ignition switch kit is compatible with the following outdoor appliance brands: Husqvarna and Craftsman.

This replacement blade adapter is an authentic OEM part for a riding lawn mower. The blade adapter is located in the lower deck of a lawn mower and connects the blade to the motor shaft. As the shaft rotates, it spins the adapter, causing the blade to rotate and cut grass. The adapter locks into place so that it doesn't come flying off during operation. The adapter is made of durable steel so that it is not easily damaged, but if the blade strikes something quite hard, it can break the adapter, causing the blade to spin unevenly, or even bending the motor shaft. If left unattended to, it can be dangerous for the operator, as the blade could potentially break off from the mower. Replacing the adapter can be a little finicky, as they are generally quite tightly locked into place. There are special adapter keys that make it easier to remove, but the same effect can be achieved with a screwdriver or a pair of pliers. This part is compatible with riding lawn mowers made by Husqvarna and Craftsman. It comes sourced from the original manufacturer and ships individually.

This replacement part is a guide kit. This is a genuine replacement part made by Husqvarna. Guide kits are small parts that connect to the side of a lawnmower to help the user create clean lines during use. The rope is looped through the guide so that the user maintains consistent work. A new guide kit might be needed if the user is unable to maintain clean lines while cutting grass. If the guide loop is worn down and will not hold rope correctly, it might be time to replace the guide kit. This repair should be fairly simple and only require common household tools such as a screwdriver and perhaps pliers if the previous piece is stuck. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This replacement part is a compression spring and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. Compression springs are very important in many different types of appliances. Springs use forces to allow the engine and other parts to operate smoothly during use.A new compression spring might be needed if the current one is missing or damaged in any way. This can include being bent or cracked. Due to the nature of their use, compression springs can become stripped over time and should be replaced when this happens. It is not unusual for springs to snap under pressure from overuse. It is recommended to refer to the user's manual before replacing this part. This is a genuine OEM replacement part to ensure proper fit and long-lasting use. This compression spring is sold individually and is sourced directly from the manufacturer.