Wed95hedw Parts

This Y-shaped hose connector joins two water inlet hoses into a single connection point for the dryer's steam system. It allows hot and cold water lines to feed into the dryer for steam-based wrinkle removal or refresh cycles. Replace this connector if you notice water leaking at the hose junction or if the steam function is not working properly due to a cracked or damaged fitting.

This is the control panel located on the front of the dryer where the user interface and control components are mounted. It provides the structural housing for buttons, knobs, or electronic displays used to select dryer cycles and settings. Replace this panel if it is cracked, warped, or damaged, causing difficulty operating the dryer controls.

Mounting screw for microwaves, dryers, wall ovens, washers, and laundry centers. Replaces lost, stripped, or damaged screws during installation or repair.

Fix unresponsive buttons or a blank display with a new dryer control panel. This repair restores cycle selection and settings. Moderate DIY install.

Dryer clip secures internal components and prevents rattling or loose parts. Replace if broken, missing, or worn to restore proper fit and function.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Control console assembly for dryers. Mounts on top of the dryer cabinet and houses the control panel. Replace if cracked, damaged, or broken.

This is a metal flange bracket that secures the heater housing assembly inside the dryer. It holds the heater box in the proper position to ensure safe and efficient heat distribution during drying cycles. Replace this bracket if it is bent, corroded, or broken, which can cause the heater housing to shift and lead to overheating or unusual noises.

This is a gray plastic timer knob that attaches to the dryer's control panel shaft. It allows you to select and set the drying cycle and time. Replace this knob if it is cracked, broken, or if the D-shaped shaft hole is worn out, causing the knob to spin freely without engaging the timer.

Exposed wiring at the back of your dryer? This terminal block cover shields electrical connections from accidental contact and debris. Simple snap-on install.

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

Exhaust vent elbow routes hot air and lint from your dryer to the external vent. Replace if cracked, bent, or leaking to restore airflow and safety.

If your dryer takes forever to dry clothes or feels overly hot, a clogged or damaged exhaust pipe may be restricting airflow. Direct replacement part.

This is a replacement door handle for a clothes dryer. It attaches to the dryer door and provides a grip for opening and closing the door. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open the dryer door.

Exterior glass panel for your dryer door. Replace when cracked, chipped, or shattered to restore visibility and protect internal components.