Wed95hedwo Parts

This shield is a molded protective cover that guards internal appliance components from moisture and debris, helping prevent damage and maintain reliable operation. It fits into place to keep nearby parts shielded and aligned. What it does:

• Covers and protects internal components from water, grease, and small debris
• Helps direct moisture away from sensitive parts to reduce corrosion risk
• Prevents rubbing and wear between adjacent parts that can cause noise
• Aids proper alignment and sealing of nearby panels and assemblies

• Disconnect power and water supply before beginning any repair
• Inspect mounting tabs and surrounding seals; replace any damaged fasteners
• Snap or screw the shield into the existing mounting points without forcing
• Replace those components before reassembly

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

This rear bracket secures the dryer's rear panel and helps align internal components for stable operation. It restores proper fit and support when the original bracket is bent, broken, or missing. What it does:

• Secures and positions the dryer's rear panel to the cabinet frame
• Supports internal components and helps maintain proper panel alignment
• Prevents rattling, vibration, and panel separation during operation
• Helps ensure consistent airflow path by keeping the rear housing properly positioned

• Disconnect power (and gas, if applicable) before servicing the dryer
• Access typically requires removing the rear panel; keep fasteners organized for reassembly
• Inspect adjacent mounting points and replace any damaged screws or clips

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.

Color: Silver  
 

Color: Chrome/Shadow

This mounting bracket secures internal components to the appliance cabinet, keeping parts aligned and stable for reliable operation. It's a simple replacement that restores proper support where the original bracket is bent, cracked, or missing. What it does:

• Provides a solid attachment point for internal panels, assemblies or hardware
• Restores alignment to components that shift or sag when a bracket fails
• Helps eliminate rattling or abnormal movement caused by a broken bracket
• Works as a direct-fit replacement when the original bracket is damaged

• One mounting bracket

• Intended for users comfortable with basic disassembly; unplug power and shut off water before starting
• Keep track of removed fasteners and any shims or spacers for proper reassembly
• Inspect surrounding parts for damage and replace any worn fasteners to ensure secure mounting

This name plate is the cosmetic identification plate for the appliance's console, restoring factory appearance and readable markings. It replaces a cracked, faded, or missing plate to make the console easy to read and look finished. What it does:

• Provides the external identification/branding plate for the control area or console
• Restores legible markings that can become faded, scratched, or worn
• Improves overall appearance when the original plate is damaged or missing
• Protects the underlying console surface from minor wear

• One name plate as shown

• Disconnect power to the appliance before starting any work
• Installation may require removing trim or console screws or peeling off old adhesive
• Handle carefully to avoid scratching the new plate; align before fastening or applying adhesive