Wed9600w1 Parts

This shield is a molded protective cover that guards internal appliance components from moisture and debris, helping prevent damage and maintain reliable operation. It fits into place to keep nearby parts shielded and aligned. What it does:

• Covers and protects internal components from water, grease, and small debris
• Helps direct moisture away from sensitive parts to reduce corrosion risk
• Prevents rubbing and wear between adjacent parts that can cause noise
• Aids proper alignment and sealing of nearby panels and assemblies

• Disconnect power and water supply before beginning any repair
• Inspect mounting tabs and surrounding seals; replace any damaged fasteners
• Snap or screw the shield into the existing mounting points without forcing
• Replace those components before reassembly

This small retaining clip secures internal trim, panels, or wiring runs to keep components in place and prevent rattles or loose connections. It restores proper fit and helps maintain safe, quiet operation. What it does:

• Holds panels, trim pieces, or wiring harnesses in position to prevent movement
• Stops rattling and wear from vibration or loose parts
• Helps maintain correct alignment of surrounding components
• Useful when replacing damaged or missing fasteners during repairs

• Disconnect power to the appliance before starting any repair
• Access may require removal of trim, panels, or other parts; retain screws and fasteners
• Clip installs by snapping into a mating hole or channel; avoid forcing to prevent breakage
• Use appropriate-size trim tools to avoid scratching surrounding surfaces

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

This exhaust pipe directs heated air from the dryer drum to the household vent, restoring proper airflow for efficient drying and reduced lint buildup. It's a direct-fit replacement designed to match the OEM airflow path. What it does:

• Channels dryer exhaust from the appliance to the external vent to maintain proper airflow.
• Helps prevent lint accumulation in the cabinet by providing a sealed exhaust path.
• Can reduce long dry times and overheating caused by restricted or damaged venting.
• Addresses symptoms such as poor drying performance, hot dryer cabinet, or noticeable burning/overheating smells near the dryer vent area.

• One exhaust pipe.

• Disconnect power (and gas, if applicable) before starting work; the appliance is fully de-energized.
• Wear gloves to avoid sharp edges; remove old pipe and clean vent connections before installing the replacement.
• Secure with appropriate clamps or fasteners and ensure a continuous, unobstructed path to the exterior vent.
• After installation, run a short cycle to check for leaks.

Size: 8-18 x 3/4 inch.

This replacement plug seals a drain or access opening to prevent leaks and keep refrigerant/condensate and debris where they belong. Fits service openings on compatible Whirlpool appliances to restore a watertight seal. What it does:

• Seals a drain, access hole, or service opening to stop water or debris from leaking out
• Helps maintain proper condensate routing and prevents pooling inside the cabinet
• Prevents pests and dust from entering through unused openings
• Simple, non-electrical part that restores the original seal and function

• One plug

• Disconnect power to the appliance before servicing; follow all safety procedures
• Press the plug firmly into the opening until fully seated; use hand pressure only unless otherwise specified
• Inspect for proper sealing and test with a small water flow before reassembling the appliance

This tech sheet provides the appliance's official service information—diagrams, wiring, and diagnostics—to help identify issues and guide safe troubleshooting. Use it to reference OEM wiring and error-code guidance before repairs. What it does:

• Shows wiring diagrams and component locations to clarify electrical connections.
• Lists diagnostic steps and error/code references used by technicians.
• Helps narrow down causes when the appliance won't start, has electrical faults, or shows error codes.
• Aids in identifying the correct service parts and circuit pathways for repair checks.

• This is an informational service sheet, not an electrical part; read fully before attempting repairs.
• Always unplug the appliance or shut off power at the breaker before doing electrical checks or part replacements.
• Use the diagram to guide testing with appropriate multimeter settings and safety gear.