Wed9720xw2 Parts

This control knob replaces a worn or broken range/dryer control knob to restore reliable selection and adjustment of settings. It provides a firm grip and clear pointer for accurate control of the appliance functions. What it does

• Turns control shafts to select temperature, cycle, or power settings
• Restores a secure grip when the original knob is cracked or loose
• Helps eliminate intermittent or inaccurate user input caused by damaged controls
• Works with the matching splined shaft style for a snug fit

• One control knob

• Pull the old knob straight off the control shaft; align the knob's splines and push the new knob on until fully seated
• If the knob is tight, use steady pressure—do not hammer or force, which can damage the shaft
• Disconnect power to the appliance before servicing electronic control areas and follow all safety guidelines

Control console assembly for dryers. Mounts on top of the dryer cabinet and houses the control panel. Replace if cracked, damaged, or broken.

Dryer won't power on or trips breaker? This terminal block plug connects power to your dryer's electrical system. Common fix for power issues.

This is a metal flange bracket that secures the heater housing assembly inside the dryer. It holds the heater box in the proper position to ensure safe and efficient heat distribution during drying cycles. Replace this bracket if it is bent, corroded, or broken, which can cause the heater housing to shift and lead to overheating or unusual noises.

This is a gray plastic timer knob that attaches to the dryer's control panel shaft. It allows you to select and set the drying cycle and time. Replace this knob if it is cracked, broken, or if the D-shaped shaft hole is worn out, causing the knob to spin freely without engaging the timer.

A replacement control knob that restores reliable manual control of a dial or selector. Fits standard splined control shafts to make setting temperatures, cycles or power levels easy and intuitive. What it does

• Provides a secure grip and clear rotation for selecting settings on the appliance's control shaft
• Replaces cracked, worn or missing knobs that are hard to turn or won't stay in position
• Restores tactile feedback and alignment so settings register correctly with the control shaft
• Useful when original knob splines are stripped or the outer cap is damaged

• Typically installs by aligning splines and pushing firmly onto the control shaft until seated
• Power to the appliance should be turned off when removing and installing control parts
• Do not force the knob onto a shaft that does not match; verify spline match before installation
• If knob does not engage or control still fails, the underlying switch or shaft may need inspection

Exposed wiring at the back of your dryer? This terminal block cover shields electrical connections from accidental contact and debris. Simple snap-on install.

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

Exhaust vent elbow routes hot air and lint from your dryer to the external vent. Replace if cracked, bent, or leaking to restore airflow and safety.

If your dryer takes forever to dry clothes or feels overly hot, a clogged or damaged exhaust pipe may be restricting airflow. Direct replacement part.

Sound absorber insulation pad for dryers. Installs inside cabinet to dampen noise and vibration. Replace if torn, compressed, or missing.

This is a protective shield that mounts along the edge of the dishwasher door. It helps prevent steam and moisture from escaping the door and damaging the surrounding cabinetry or countertop. Replace this shield if it is warped, cracked, or missing, or if you notice moisture damage around the dishwasher door area.

This is a replacement door handle for a clothes dryer. It attaches to the dryer door and provides a grip for opening and closing the door. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open the dryer door.

Wire harness for your dryer's internal electrical connections. Replace this component if wires are frayed, damaged, or connectors are broken or loose.

Secures internal dryer components in proper position. Replace this retaining ring if cracked, broken, or missing to prevent parts from shifting or slipping.