Wfe3211ws Parts

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays properly aligned, helping the door seal engage correctly for safe, reliable operation.

• Supports the weight of the door and controls opening/closing motion
• Helps maintain door alignment so latches/seals engage properly
• Wear or damage can cause sagging, rubbing, squeaking, or difficulty closing
• A misaligned door may prevent the unit from starting or sealing correctly

• Disconnect power and allow the appliance to cool before servicing
• Use gloves and eye protection; doors can be heavy and spring-loaded
• Support the door during removal to prevent damage
• Transfer any hardware from the old hinge to the new one if re-usable

This front leveling leg adjusts the height at the front of your appliance to keep it level and steady. Replacing a worn or missing foot helps eliminate rocking, protect floors, and make fine leveling adjustments simple.

• Threads into the base at the front corner to raise or lower the unit for accurate leveling
• Stabilizes the appliance to minimize rocking and vibration when opening the door or using the cooktop
• Restores proper adjustment when the original foot is stripped, bent, or missing
• Common signs include a wobbling appliance, difficulty leveling, or metal-to-floor contact/scuffing

• Disconnect power; turn off the gas supply
• Protect the floor and use an assistant to carefully slide and tip the appliance
• Start the new leg by hand to avoid cross-threading; finish adjustment with a wrench
• Level front-to-back and side-to-side, then verify stability before restoring service

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

The Anti Tip Bracket is an OEM component specifically designed for Whirlpool ranges. This bracket plays a crucial safety role in preventing the range from accidentally tipping over if excessive weight is applied to the open oven door. 

The anti-tip bracket secures tightly to the floor or wall behind the range, linking it securely in place. It allows the oven door to function while ensuring the entire appliance remains stable even under heavy use. 

Causes of a bad bracket can include damage, deterioration of mounting hardware over time, or failure to install properly according to manufacturer instructions. 

Symptoms of a faulty anti-tip bracket include:

• The range appears unsecured and able to wobble or rock backward 
• Looseness between the bracket and mounting surface
• Cracks or breaks in the anti-tip bracket material

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 
 

This surface element supplies heat to a cooktop burner zone. Replace a failed element to restore reliable, even heating and consistent temperature control so your range responds properly when you adjust the knob.

• Converts electrical energy into radiant heat for cooking
• Cycles on/off to maintain the temperature set by the control
• Resolves: burner won't heat, heats slowly or intermittently, stuck on high/low, or visible hot spots/damage
• Helps address nuisance tripping from a shorted element

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• Access typically requires lifting/removing the cooktop; note wire locations and transfer one at a time
• Handle the element by the frame; avoid touching the heating surface and secure all clips/brackets as found
• Test the burner operation before final reassembly

Color: Black. For biscuit order 98008169. For white order WP98008544.

This 10-32 terminal block nut fastens wire lugs to the appliance's terminal studs. Replacing a missing, stripped, or corroded nut restores a tight, reliable connection and helps prevent heat damage or intermittent power at the connection.

• Secures wire lugs to a 10-32 terminal stud for a solid electrical connection
• Restores proper clamping force when the original nut is stripped, corroded, or missing
• Helps address loose/burned terminal connections, heat discoloration, or intermittent power at the block
• Suitable for terminal block and similar 10-32 stud applications on compatible appliances

• Disconnect power at the breaker or unplug the appliance before servicing
• Inspect the terminal block, studs, and wiring for heat damage; replace any damaged components
• Clean threads and start the nut by hand to avoid cross-threading; tighten firmly without overtightening
• If the stud turns while tightening, hold it with an appropriate tool to protect the block

This factory wire harness is the pre-terminated wiring assembly that links key components inside your appliance. Replacing a damaged harness restores reliable electrical connections and can help resolve dead, intermittent, or erratic operation of individual functions. What it does:

• Distributes power and signals between the control and components such as motors, switches, heaters, sensors, and lights
• Provides model-specific, correctly keyed connectors and lengths for secure, clean routing
• Helps correct issues from burnt, broken, pinched, or corroded wires and loose/melted connectors
• Symptoms can include components not running, intermittent operation, error codes, or visible heat damage at connectors

• 1 wire harness assembly

• Disconnect electrical power before servicing; if applicable, also shut off water or gas supplies
• Photograph existing routing and connections to match the original layout during reassembly
• Route the new harness away from sharp edges, moving parts, and hot surfaces; secure with existing clips/ties
• Seat each connector fully until locked; inspect mating terminals for heat damage and address as needed

This door-activated switch detects when the oven door opens or closes and signals the appliance to control the interior light. Replacing a worn or failed switch restores dependable light operation and accurate door-status feedback.

• Senses oven door position and opens/closes the light circuit
• Controls the oven's interior light based on door position
• Provides door-status input to the control for normal operation
• Typical symptoms: light stays on, won't turn on, or flickers with door movement; door-ajar messages may appear

• Disconnect power at the breaker or unplug the unit before servicing
• Access the switch from behind the front frame or control area, depending on model
• Move wires to the new switch one at a time to maintain correct positions; secure with existing hardware
• Restore power and verify light operation with door open/closed before reassembly

This replacement terminal block cover encloses the appliance's incoming power connections. It protects the wire terminals from accidental contact and debris, restoring a safe, finished connection area when the original cover is damaged or missing. What it does:

• Covers and shields the power terminal block where the supply wires connect
• Helps prevent accidental contact with live electrical connections
• Helps keep dust and debris out of the connection area
• Common signs: missing or broken cover, cover won't stay attached, visible heat damage or discoloration on the original cover

• One terminal block cover

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal block per your model's service information
• Reuse existing mounting hardware; position and secure the new cover without pinching wires
• Inspect wires/terminals for heat damage or looseness and correct before reassembly

This support bracket secures an appliance cabinet component or mounting point to restore alignment and reduce movement. It replaces worn or broken supports so panels and internal parts stay properly positioned during normal operation. What it does

• Holds a cabinet panel, frame, or internal component in place to maintain proper alignment.
• Stabilizes mounting points to help reduce vibration, rubbing, or intermittent noise.
• Common replacement when you notice a loose or sagging panel, rattling, or unusual chassis movement.
• Provides a direct mechanical fix—matches the OEM bracket design and fit.

• Disconnect power (and shut off gas supply for gas appliances) before starting any repair.
• Remove necessary panels and fasteners to access the old bracket; keep track of all screws and clips.
• Compare the new bracket to the old part for orientation before installing; secure using the original fasteners—do not overtighten.

This frame surrounds and supports the window glass in your oven door, keeping the glass secure and aligned. Replace a bent or corroded frame to address loose glass and restore the door's proper fit and clean appearance.

• Secures the oven door window glass within the door assembly
• Helps maintain alignment and seal around the window area
• Replaces frames that are bent, cracked, or corroded
• Addresses loose, rattling, or misaligned door glass
• Restores the finished look of the door

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's instructions and place it on a padded surface
• Handle glass with cut-resistant gloves; keep track of screws, clips, and insulation for transfer
• Seat the glass evenly and avoid overtightening fasteners during reassembly

Mounting bracket that secures a drawer to its cabinet or glide assembly, restoring stability and alignment for smooth opening and closing. Replaces damaged or missing brackets that cause sagging, misalignment, or detachment. What it does:

• Secures the drawer to the cabinet or slide hardware so the drawer stays aligned and supported.
• Restores smooth opening and closing when a worn or broken bracket causes binding or uneven travel.
• Prevents the drawer from sagging, pulling out, or detaching from the glide.
• Use when bracket is cracked, bent, or missing to regain proper drawer function.

• Disconnect power to the appliance or unplug it before beginning work.
• Basic hand tools are typically required; keep original fasteners for reuse if they are undamaged.
• Remove the drawer and inspect the glide/rail for damage before installing; reinstall drawer and verify smooth operation.

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

Qty 4 needed to complete full insulation

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.