Wfe374lvs Parts

Color: Black

This wire harness is the appliance's main electrical connector assembly that routes power and signals between components, restoring reliable electrical connections for controls and motors. Use it to replace a damaged, burnt, or broken harness. What it does:

• Carries power and control signals between the appliance's control board, motors, switches, and sensors
• Replaces damaged wiring that can cause intermittent operation, non-responsive controls, or failure to start
• Restores proper connector fit and secure splices to prevent arcing and poor contact
• Helps eliminate issues caused by frayed insulation, broken terminals, or melted wires

• One complete wire harness assembly

• Disconnect the appliance from power (unplug or switch off breaker) before starting any repair
• Compare the new harness to the old one for connector type and routing before disconnecting components
• Route wires along the original paths and secure with existing clips or ties to avoid heat and pinch points

The Surface Element is an OEM part for Whirlpool ranges. It is responsible for providing the heat necessary for cooking on the stovetop. Designed to fit seamlessly into the range, this element ensures even heating and efficient energy use, allowing for precise temperature control during cooking.

Causes of a bad surface element can include normal wear and tear, electrical faults, or damage from cookware. Over time, repeated heating and cooling cycles can cause the element to degrade, while physical impacts or spills can also lead to malfunction.

Symptoms of a bad surface element include:

• Inconsistent or uneven heating
• The element not heating up at all
• Visible damage or burn marks on the element
• Sparks or unusual noises when the element is turned on

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: 3000/1400W - Left front element

This spacer provides a precise gap for proper alignment and clearance between components, helping maintain correct part positioning for reliable operation. It's a simple replacement that restores intended spacing and reduces wear. What it does:

• Positions and separates adjoining parts to maintain correct clearance
• Helps prevent rubbing, misalignment, or binding of moving components
• Restores factory spacing after maintenance or part replacement
• Fits where the original spacer was used to support assembly alignment

• One spacer as shown

• Inspect surrounding components and mounting surfaces for damage before installing
• Remove power to the appliance and follow manufacturer service instructions
• Install in the same orientation as the original spacer and verify proper clearance
• If fasteners or adjacent parts are worn, replace them to ensure a secure fit

This oven rack is a replacement wire rack that restores stable support for cookware and bakeware, letting trays and pans slide in and out smoothly. It fits into the oven's rack supports to provide even cooking placement. What it does:

• Provides a stable shelf for baking sheets, pans, and cookware inside the oven
• Slides on oven rack supports to position food closer or farther from heat
• Replaces bent, warped, or missing racks that prevent stable placement
• Helps maintain even airflow and cooking clearance by restoring proper rack height

• One replacement oven rack

• Install by sliding rack into the oven's existing rack supports until fully seated
• No special tools required; handle edges carefully to avoid pinching
• Remove racks before using self-clean cycle; allow oven to fully cool before handling
• Use oven mitts or gloves when inserting/removing while hot

This replacement drawer panel restores the exterior trim and alignment of a refrigerator/freezer drawer for a clean, finished look. It replaces damaged or worn panels to help the drawer close and operate as intended. What it does:

• Replaces cracked, dented, scratched or discolored drawer front trim
• Restores proper front alignment and helps ensure the drawer closes smoothly
• Provides the cosmetic finish that matches the appliance's lower drawer
• Secures to the drawer assembly using existing fasteners and mounting points

• Disconnect power to the appliance before beginning work
• Remove the drawer assembly to access mounting screws and clips as needed
• Keep original fasteners and trim pieces; transfer them to the new panel unless replacements are supplied

Color: Black. For white use 9758491

Color: White  Note: Right side endcap