Wfe770hf20 Parts

This wire harness is the appliance's main electrical connector assembly that routes power and signals between components, restoring reliable electrical connections for controls and motors. Use it to replace a damaged, burnt, or broken harness. What it does:

• Carries power and control signals between the appliance's control board, motors, switches, and sensors
• Replaces damaged wiring that can cause intermittent operation, non-responsive controls, or failure to start
• Restores proper connector fit and secure splices to prevent arcing and poor contact
• Helps eliminate issues caused by frayed insulation, broken terminals, or melted wires

• One complete wire harness assembly

• Disconnect the appliance from power (unplug or switch off breaker) before starting any repair
• Compare the new harness to the old one for connector type and routing before disconnecting components
• Route wires along the original paths and secure with existing clips or ties to avoid heat and pinch points

This oven cavity insulation panel helps reduce heat loss and improves temperature stability inside the oven for more even cooking. It replaces worn or damaged insulation that can allow heat to escape or make the exterior hotter than normal. What it does:

• Provides thermal barrier between the oven cavity and outer cabinet to help maintain internal temperature
• Reduces heat transfer that can cause the exterior surfaces to become unusually hot
• Helps prevent excessive heat loss that can affect cooking performance and energy use
• Fits behind the oven liner where original insulation is mounted

• One oven cavity insulation panel

• Disconnect power (and gas, if applicable) before starting any repair
• Handle insulation with gloves; avoid compressing or tearing the material
• Follow the appliance service manual for proper placement and secure mounting

This right-side slide drawer supports and guides the refrigerator/freezer drawer so it opens and closes smoothly, restoring proper alignment and operation. Simple replacement can stop sagging, sticking, or noisy drawer movement. What it does

• Replaces a worn or broken right-side drawer slide to restore smooth sliding and proper alignment
• Helps prevent the drawer from falling, sticking, or binding when opening or closing
• Supports drawer weight and ensures even movement along the rail
• Works with the existing left-side slide and drawer assembly to maintain fit and seal

• One right-side slide drawer

• Disconnect power to the appliance or remove food and secure contents before service
• Remove the drawer per your model's service instructions to access and replace the slide
• Retain original fasteners and match orientation (right-side) during reassembly
• If you encounter damaged mounting clips or screws, replace them before finishing reassembly

This spacer provides a precise gap for proper alignment and clearance between components, helping maintain correct part positioning for reliable operation. It's a simple replacement that restores intended spacing and reduces wear. What it does:

• Positions and separates adjoining parts to maintain correct clearance
• Helps prevent rubbing, misalignment, or binding of moving components
• Restores factory spacing after maintenance or part replacement
• Fits where the original spacer was used to support assembly alignment

• One spacer as shown

• Inspect surrounding components and mounting surfaces for damage before installing
• Remove power to the appliance and follow manufacturer service instructions
• Install in the same orientation as the original spacer and verify proper clearance
• If fasteners or adjacent parts are worn, replace them to ensure a secure fit

This main back insulation panel replaces the factory foam insulation behind the refrigerator cabinet to help reduce heat transfer and minimize noise. Installing the correct back insulation helps the refrigerator maintain temperature more consistently. What it does:

• Provides thermal barrier behind the cabinet to slow heat gain from the rear.
• Helps limit compressor and airflow noise by absorbing sound near the rear cavity.
• Commonly replaced when insulation is damaged, missing, compressed, or when the appliance has higher-than-normal run times or inconsistent cooling.
• Protects internal components from external temperature swings and debris entering rear cavities.

• Disconnect power before accessing the rear of the appliance and remove any rear access panels or brackets to reach the insulation location.
• Handle the panel gently to avoid tearing or compressing the insulation; secure using original clips/adhesive or replacement fasteners as applicable.
• Ensure the insulation fits flush and does not interfere with wiring, tubing, or moving parts.

This inner oven door liner replaces the damaged or warped inner panel that supports the oven door glass and helps contain heat inside the oven cavity. It restores a solid mounting surface for door glass and internal components. What it does:

• Provides the inner structural panel for the oven door and supports the door glass and insulation.
• Helps maintain proper oven heat containment to support uniform cooking.
• Prevents direct exposure of insulation and internal parts to oven cavity heat and food debris.
• Addresses symptoms like visible cracks, warping, or detached glass mounting points on the inside of the door.

• Disconnect power before starting any repair and follow manufacturer's safety instructions.
• Remove the oven door per the appliance manual to access and replace the inner liner; handle glass and sharp edges carefully.
• Keep all original screws and mounting clips; confirm screw locations during disassembly to ensure proper reassembly.
• If the door has multiple glass panels or seals, verify placement during reassembly—do not force parts into position.