Wfmc8401uc Parts

Fix washer control or display issues with this cable harness. Connects main control to components. Moderate repair requiring panel access.

This hose inlet is the water inlet connection that directs incoming water into the appliance, restoring a secure supply path and helping prevent leaks at the entry point. What it does

• Provides the sealed connection point for the incoming water supply hose.
• Routes water into the appliance's fill system so cycles can start and run properly.
• Helps prevent leaks where the external supply hose attaches.
• Commonly replaced when water won't enter, the connection leaks, or the inlet is damaged.

• One hose inlet connection.

• Turn off the water supply and disconnect power before replacing.
• Inspect existing seals or gaskets; replace if cracked or worn.
• Tighten connections to hand-firm plus a quarter turn; avoid overtightening.
• After installation, restore water and power and check thoroughly for leaks during a fill cycle.

Delivers hot water from your heater to the washer. Replace if leaking, cracked, or damaged to prevent water damage. Verify fit with your model number.

This sleeve is a small guide/bushing used in select Bosch-built appliances. It spaces and supports a moving component to keep it aligned and reduce friction, helping the mechanism operate smoothly and quietly.

• Acts as a bushing/spacer around a pin or shaft to guide motion
• Helps maintain alignment of connected parts
• Reduces friction and wear between mating surfaces
• A worn or missing sleeve can cause wobble, rough movement, or squeaking/clicking noises

• Disconnect power and shut off water before servicing
• Note the sleeve's orientation and seated depth during removal to match on installation
• Inspect the mating pin/shaft and surrounding parts; replace if worn for best fit
• Verify smooth movement by hand before reassembly and testing

The Drive Motor is an OEM replacement part for Bosch washing machines. This powerful motor is responsible for driving the drum rotation during the wash and spin cycles.

A bad drive motor can occur due to electrical faults, mechanical issues, or normal wear and tear over time. Signs of a faulty drive motor include the drum not spinning or agitating, unusual noises coming from the motor, or the washer not starting at all.

Symptoms of a bad drive motor include:

• The drum not spinning or agitating  
• Unusual noises
• The washer not starting  

Replace your faulty washer drive motor with this genuine OEM Bosch part to restore your washing machine. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

Spring tank secures and positions an appliance tension spring to maintain proper movement and balance for a door or other moving assembly. Replacing a worn or broken tank restores correct spring alignment and smoother, more reliable operation. What it does:

• Holds the end of the tension spring and keeps it aligned in the assembly.
• Maintains correct spring tension so doors or panels open, close and remain balanced.
• Prevents spring detachment that can cause sudden drops, misalignment or noisy operation.
• Common symptoms of a failing tank: door drops or won't stay open, uneven closing, rattling or banging during movement.

• Disconnect power to the appliance before starting any repair to avoid electrical hazards.
• Support the door or moving panel while replacing the tank to prevent sudden movement or injury.
• Use the OEM part orientation and hardware; inspect the spring and mounting points for wear and replace if scored or damaged.
• Test the door/panel operation several times after installation to ensure correct tension and secure mounting.

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

Replacement screw for securing panels, brackets, and components in washers, dryers, and other appliances. Needed when original screws are rusted, stripped, or missing.

This cover protects internal components and provides a finished appearance. Replace if cracked, broken, or missing to restore proper enclosure.

Fix a washer that won't start or stops mid-cycle with a faulty door lock. This mechanical locking assembly secures the door during wash cycles.

Fix washer water level issues or won't fill correctly with a new pressure chamber. This part regulates water sensing for proper fill cycles.

This interference capacitor reduces electrical noise and helps protect the appliance's control circuitry from voltage spikes. It's a direct-replacement noise suppressor used where EMI/RFI filtering is required for reliable operation. What it does:

• Suppresses electromagnetic and radio-frequency interference that can affect controls and electronics
• Helps prevent false signals or erratic behavior caused by electrical noise
• Supports stable operation of motors and electronic control boards
• Can reduce audible electrical noise or interference-related symptoms

• Disconnect power at the breaker before inspecting or replacing the capacitor
• Discharge the capacitor and avoid touching terminals; use insulated tools
• Verify wiring match and polarity before connecting

Drive pulley for washer drum and motor belt system. Replaces worn, cracked, or damaged pulleys that cause belt slippage or wobbling during operation.