Wfvc4400uc Parts

This white dispenser tray replaces a damaged or stained refrigerator dispenser drip tray to keep the area under the dispenser clean and catch spills. Restores proper fit and appearance for an even, tidy look. What it does:

• Collects drips and spills from the dispenser to protect the cabinet and floor
• Provides a finished, easy-to-clean surface under the dispenser area
• Snaps into the dispenser opening and holds securely under normal use
• Helps reduce odors and build-up by catching liquids before they reach internal surfaces

• Unplug or power off the appliance before removing the old tray
• Remove any standing water and debris, then lift or slide out the old tray per the appliance's user manual
• Align the new tray's tabs/rails with the dispenser opening and press until it seats
• If any clips are damaged or the tray doesn't seat securely, inspect surrounding trim before forcing into place

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

The Control Module is an OEM component specifically designed for Bosch washers. As the command center for all wash functions, the control module is responsible for operating cycles, temperatures, water levels and more based on user selections.  

Causes of a bad control module can include wear and tear over time as the control module coordinates thousands of complex processes during machine operation. Exposure to moisture or impacts may also potentially damage electronic components.

Symptoms of a bad control module include:

• The washer not starting or responding to commands
• Inability to select or change wash cycles  
• Fault codes displayed
• Random or unexpected behaviors during the operation

This OEM Bosch part is also compatible with some Kenmore, LG, Maytag, Whirlpool, and Frigidaire models. 

This replacement hose-pressure chamber routes water to the dishwasher's pressure chamber so the machine can sense and control water level. Restores proper pressure sensing to help prevent overfilling and fill errors. What it does

• Connects the sump/water path to the pressure chamber so the water-level sensor can detect fill height.
• Replaces cracked, pinched, or collapsed hose that can cause inaccurate water-level readings.
• Commonly used when dishwasher shows overfill, won't fill correctly, or reports water-level or pressure-related errors.
• Flexible vinyl tubing designed for routing in tight spaces without kinking.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect nearby fittings and the pressure chamber for wear; replace clamps if damaged.
• Push-fit or clamp the hose securely to both ports; ensure there are no kinks or sharp bends.

This small mounting spacer positions and cushions appliance components to keep panels and parts aligned and reduce vibration. It restores correct clearance between parts for smoother, quieter operation. What it does:

• Keeps consistent gap and alignment between adjacent components or panels
• Cushions against vibration to help reduce rattling or noise
• Helps maintain proper fit of trim, panels, or assemblies that rely on a spacer
• Worn or missing spacers can cause misaligned panels, noise, or uneven gaps

• Disconnect power and water before accessing the area.
• Access may require removing trim, panels, or adjacent components; keep fasteners organized.
• Replace like-for-like; do not force parts into place—verify correct orientation before final assembly.

This hose inlet is the molded connection that routes incoming water into the appliance and provides a sealed mating point for the fill hose. It restores proper water flow and helps prevent leaks at the hose connection. What it does

• Directs incoming water from the fill hose into the appliance's water system.
• Provides a sealed connection to prevent drips or leaks at the hose attachment.
• Can cause no-fill or slow-fill symptoms when cracked, clogged, or loose.
• Works with the inlet hose and nearby fittings to maintain correct water supply.

• Turn off power to the appliance and shut off the water supply before starting.
• Inspect and replace any damaged gaskets or clamps when installing this part.
• Hand-tighten fittings, then snug with appropriate tools; avoid overtightening plastic fittings.
• After installation, restore water and power, run a short cycle, and check all connections for leaks.

This chrome outer door ring replaces a scratched, dented or missing trim piece to restore the washer door's finished appearance and keep the door edge protected. It's a direct-replacement exterior trim ring. What it does

• Replaces damaged or bent chrome trim around the front-load washer door.
• Restores cosmetic finish and conceals the door edge.
• Helps maintain a uniform seal surface by keeping the door edge supported.
• Useful when trim is cracked, loose, or missing and detracts from operation or appearance.

• Disconnect power before beginning any door disassembly.
• Remove the outer door panel or bezel per OEM instructions to access the trim; handle door glass and bezel carefully to avoid breakage.
• Typical installation requires basic hand tools (screwdriver/torx) and alignment of the trim to the door bezel.

This cable harness routes power and control signals between the dishwasher control board and components, restoring reliable electrical connections for proper operation. Designed to replace damaged or worn wiring where connectors or insulation are compromised. What it does:

• Transfers power and control signals between the main control/module and subsystems (pumps, valves, sensors, motor)
• Replaces frayed, burned, or broken wires and damaged connector ends that cause intermittent operation or component failures
• Restores proper connector fit and wiring routing to prevent shorts and miscommunication
• Helps resolve symptoms like no power to components, intermittent function, or visible wiring damage

• Disconnect power to the appliance before starting work to avoid shock or damage
• Keep track of connector positions; take photos before removing the old harness for accurate reinstallation
• Route the new harness along the same path and secure any clips or ties to prevent pinching or contact with moving parts
• If you encounter corrosion or damaged connectors on mating parts, inspect and replace those components as needed

This inner door panel replaces a damaged or corroded dishwasher door interior to restore a clean, sealed surface and proper latch alignment. Designed to match factory fit and help prevent leaks and improve door operation. What it does:

• Replaces the dishwasher's interior door surface to protect insulation and internal components
• Restores a flat sealing surface to help the door latch and close properly
• Reduces risk of leaks caused by dents, cracks, or corrosion in the inner door
• Helps maintain proper alignment for the door gasket and mounting hardware

• Disconnect power and water supply before beginning any repair
• Handle panel edges carefully to avoid cuts; wear gloves if needed
• Require removing outer door panel, inner trim, or door screws—keep fasteners organized

This T-shaped water hose connector routes incoming water to separate internal hose lines, restoring proper water distribution inside the appliance. It replaces a worn or cracked hose tee to stop leaks and restore flow to internal components. What it does:

• Joins three water lines so water can be directed to multiple internal points
• Stops leaks caused by cracked or damaged tee fittings at hose junctions
• Restores reliable water flow to downstream parts that depend on the split connection
• Prevents hoses from separating at a failing junction

• Turn off and disconnect the appliance from the water supply before servicing
• Inspect hose ends and clamps; replace clamps or seals if worn
• Push hoses fully onto each barb and secure with appropriate clamps
• After installation, restore water and check all connections for leaks

This fastening ring secures mating appliance components by locking parts in place to prevent movement or separation during operation. It's a simple yet essential hardware piece that helps maintain proper alignment and reliable function. What it does

• Holds mating parts together to prevent wobble, vibration, or dislocation
• Keeps seals and assemblies properly seated to reduce noise and misalignment
• Helps maintain correct component spacing for smooth operation
• Commonly replaced when the original ring is bent, worn, or missing

• Designed for use with compatible OEM assemblies; follow for correct placement
• Inspect mating surfaces and replace any damaged clips, seals, or gaskets before reassembly
• Use proper tools to avoid deforming the ring during installation; do not force into place
• Disconnect power and follow safety procedures before servicing the appliance