Wfw70he Parts

This direct hose assembly routes water or drain flow to restore proper operation and stop leaks caused by cracked or worn tubing. Designed to replace a damaged hose and help prevent water damage and poor drainage. What it does:

• Directs water or drain flow between appliance components to maintain proper plumbing function.
• Stops leaks and reduces the chance of water pooling or unintended discharge from worn or cracked hoses.
• Common symptoms addressed: visible leaks, water under or around the appliance, slow or inconsistent draining.

• Disconnect power and shut off the water supply before starting any repairs.
• Inspect hose ends and connections for damage; replace clamps or seals if corroded or worn.
• Secure hose with appropriate clamps and route to avoid kinks or pinch points.
• After installation, restore power and water, run a short cycle, and check all connections for leaks.

This wire harness routes power and signals between an appliance's control and internal components to restore reliable electrical connections. Replacing a damaged harness helps stop intermittent operation and power loss for safer, more consistent performance. What it does:

• Routes power and control signals between the control board and internal components.
• Replaces frayed, cut, or burned wiring that can cause intermittent operation or component failures.
• Helps address symptoms such as loss of power to controls, unresponsive cycles, or devices that won't start.
• Prevents loose or corroded connections that can create intermittent faults.

• Always disconnect the appliance from power (unplug or switch off circuit breaker) before servicing.
• Match each connector to its mating plug and follow the OEM wiring diagram for routing and color codes.
• Secure the harness away from heat sources and moving parts; use existing clips and fasteners.

This air trap assembly replaces the factory air trap that helps control air in the refrigerator water line, restoring steady water flow to the dispenser and ice system for more reliable fills and reduced sputtering. What it does:

• Creates a controlled air pocket in the water line to prevent sputtering or intermittent flow at the dispenser and ice maker.
• Helps maintain consistent water delivery so the ice maker can fill reliably.
• Reduces the chance of air-related filling issues and noisy gurgling from the water line.
• Fits into the appliance's water plumbing as a dedicated inline assembly.

• Always unplug the appliance and shut off the water supply before beginning service.
• Inspect tubing and fittings for damage; replace any brittle or cracked lines to ensure a leak-free connection.
• Use hand tools; avoid overtightening fittings which can damage the part or tubing.
• After installation, restore water and power, run several dispense/fill cycles, and check all connections for leaks.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This genuine replacement power cord restores electrical connection to your appliance so it can safely receive power. It replaces a damaged or worn cord to help eliminate power loss and reduce electrical hazards. What it does:

• Provides the electrical connection between the appliance and your home's power supply
• Replaces frayed, cracked, or burned cord insulation and damaged plugs
• Helps stop intermittent power issues caused by a faulty cord or connector
• Restores safe, reliable power routing when the original cord is compromised

• Always disconnect power at the breaker or unplug the appliance before installing
• Follow the appliance wiring diagram and route the cord to avoid heat or pinch points
• Secure strain relief and connectors per the manufacturer's instructions

Size: 10-24 x 3/8 inch.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This inner door panel restores the washer lid's interior finish and structural support, helping the lid close and seal properly. It replaces a cracked, dented, or cosmetically damaged inner door to improve appearance and function. What it does:

• Provides the interior surface and mounting points for the washer top lid assembly
• Restores proper lid alignment and helps the lid close smoothly
• Eliminates sharp edges or cosmetic damage from a cracked or dented inner door
• Helps maintain correct fit with the outer door and lid components

• One inner door panel

• Disconnect power and water supply before starting any repair
• Remove the outer lid and related fasteners to access and replace the inner panel
• Keep track of screws and clips; hand-tighten fasteners to avoid stripping

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This dispenser handle assembly restores proper operation and control of your refrigerator's ice and water dispenser. It replaces a cracked, loose, or broken handle so you can dispense without difficulty and improve the dispenser's appearance. What it does

• Replaces damaged or cracked dispenser handle so the lever engages properly
• Provides a secure grip for activating the ice and water dispenser
• Helps stop wobbling or sticking that prevents consistent dispensing
• Restores alignment and tactile feedback for dispenser operation

• Disconnect power to the refrigerator before starting any work to avoid electrical hazard.
• Remove the old handle by accessing the dispenser trim and fasteners; retain mounting screws if reusing.
• Align the new handle, secure fasteners, and verify the dispenser lever moves freely and dispenses correctly.

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This stator is the stationary motor component that creates the magnetic field needed for the washer's drive motor to operate. It restores motor function so the appliance can agitate and spin normally. What it does:

• Generates the magnetic field that interacts with the rotor to drive the motor.
• Enables proper agitation and spinning when the motor and rotor are functioning.
• Commonly replaced when motor runs poorly, makes unusual noises, or the washer fails to spin.
• Works as part of the motor assembly to maintain consistent motor performance.

• One stator

• Disconnect power and water supply before beginning any repair.
• Access typically requires removing the washer cabinet or motor housing; follow the service manual for your model.
• Inspect the rotor/motor and wiring for damage when replacing the stator.