Whdsr417doww Parts

Includes 12 washers.

This small bushing fits the washer's lid hinge to provide a smooth, stable pivot. Replacing a worn hinge bushing restores proper lid alignment and helps reduce squeaks, rubbing, or excessive play when opening and closing the lid. What it does:

• Acts as a low-friction sleeve between the hinge pin and bracket
• Supports smooth lid movement and helps maintain alignment
• Reduces metal-on-metal wear and hinge noise
• Symptoms of wear can include squeaking, binding, scraping, or a loose/wobbly lid

• 1 hinge bushing

• Disconnect power before servicing
• Support the lid to prevent it from dropping when the hinge is loosened
• Remove hinge hardware to access and swap the bushing; reassemble and check lid alignment
• Many models use a bushing on each hinge—inspect both sides and replace as needed

Secure your washer's drain hose with this drain hose strap. It keeps the hose positioned at the standpipe or laundry tub, helping prevent movement, dislodging, and messy leaks when vibration increases during drain and spin cycles.

• Secures the drain hose to a standpipe or utility sink, per installation guidelines
• Helps prevent the hose from backing out or spraying water during operation
• Reduces strain and kinking by keeping the hose routed in place
• Replaces a missing, cracked, or broken strap

• Unplug the washer and turn off water supply before starting
• Position the drain hose in the standpipe or tub and tighten the strap to secure it without kinking the hose
• Maintain the manufacturer-recommended air gap and hose height per your installation manual
• Run a quick drain/spin to ensure the hose stays secured and there are no leaks

Size: 14-10 a trt 7/8 s.

This 2-speed clutchless motor replaces the washer's drive motor to restore agitation and spin without a mechanical clutch. It provides the two common drive speeds used for agitate and spin cycles on compatible top-load washers. What it does:

• Turns the washer tub/agitation mechanism to enable agitate and spin functions
• Operates at two speeds (agitate and spin) using an internal clutchless design
• Commonly used when a washer hums, runs but won't agitate or spin, or fails to change between agitate and spin
• Works with the existing mounting bracket and wiring harness on compatible models

• Disconnect power before servicing to avoid shock or injury
• Motor is heavy and may require lifting assistance; support the tub during removal/installation
• Reuse the existing mounting hardware and wiring harness
• Follow the washer's service manual for disassembly, torque, and wiring routing; test operation before reassembling the cabinet

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

Size: 8-32 t. Includes 12 screws.

Size: 8-18 ab.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit

Size: 8 - 18 ab.

Alignment pin keeps the appliance door hinge aligned so the door closes evenly and seals correctly. Replacing a damaged pin restores proper door fit and helps stop sagging, rubbing, or uneven gaps. What it does:

• Positions and secures the door hinge during normal operation
• Restores correct hinge alignment when pins are worn or bent
• Helps eliminate door sag, misalignment, grinding, or difficulty closing
• Works with the hinge assembly to maintain an even seal and proper door movement

• Disconnect power to the appliance before beginning any repair; ensure the appliance is stable and cool.
• Support the door or hinge assembly while removing and installing the pin to avoid dropping or misaligning heavy components.
• Use basic hand tools; ensure pin orientation and full engagement in the hinge before testing.
• Keep small parts and fasteners secure during reassembly and test the door several times to ensure proper operation.

This is a 6-20 x 3/8 in. appliance screw used to secure panels and components. It provides a simple replacement fastener to restore proper fit and stability to the affected area. What it does:

• Fastens appliance panels, brackets, or small components where a 6-20 x 3/8 in. screw is specified
• Replaces damaged, stripped, or missing screws that cause loose panels or rattling
• Restores proper alignment and reduces vibration-related noise
• Matches the original thread size and length used in many factory assemblies

• One 6-20 x 3/8 in. screw

• Use the correct screwdriver or nut driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power or take appropriate safety precautions when working near electrical components
• If fasteners mount to plastic, consider using gentle, even pressure to prevent cracking