Wm1163xvs1 Parts

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings

A replacement clamp assembly that secures flexible hoses or tubing to fittings to help prevent leaks and minimize movement. Fits OEM mounting points and restores a tight hose connection for reliable operation. What it does:

• Secures a water or drain hose to a nipple or fitting to stop slipping and reduce leaks
• Helps maintain a sealed connection under normal pressure and vibration
• Reduces hose movement that can cause wear, noise or intermittent leaks
• Useful when the original clamp is corroded, damaged or no longer holds tightly

• Turn off power and shut off water supply before starting work
• Inspect hose and fitting; replace hose if damaged or excessively worn
• Use appropriate pliers or a screwdriver to remove/install the clamp; avoid over-tightening

This ball bearing supports a rotating shaft in the drive system, reducing friction so the appliance runs smoother and quieter. Replacing a worn bearing can curb rumbling and help prevent damage to adjoining shafts, housings, or seals.

• Supports and centers a rotating shaft within the assembly
• Reduces friction and wear between moving parts for smooth operation
• Helps limit noise and vibration from the drive system
• Common symptoms of failure include grinding/roaring noises, excessive play or wobble, rough or stiff rotation by hand, or seized rotation

• Disconnect power and, if applicable, shut off water before servicing
• Access the bearing by disassembling the related housing; note orientation and order of components
• Press the bearing out/in with a driver or press; do not hammer on the inner or outer race
• Inspect the shaft and any companion seals or bearings; clean the bore and seat the new bearing fully

Connector hose joins an appliance water line to internal plumbing, providing a sealed path for water. Replacing a damaged connector stops leaks and restores reliable water delivery to dispensers and ice makers.

• Joins and seals the appliance water line to the unit, preventing leaks and ensuring proper flow.
• Replace when you notice dripping, pooling under the appliance, or reduced water/ice production.
• Fits factory connection points for a secure, leak-resistant seal.
• Works with existing clamps and O-rings when those components are serviceable.

• Shut off the water supply and disconnect power before removing the old connector.
• Relieve water pressure by running the dispenser or dispensing water before disconnecting lines.
• Inspect and replace worn clamps or O-rings; hand-tighten fittings, then turn the water on slowly and check for leaks.

This bellows is the flexible door boot gasket that seals the front-load washer door to prevent water leaks and keep laundry contained during cycles. Replaces a worn, torn or brittle boot to restore the tub seal. What it does:

• Forms a watertight seal between the washer door and tub to help prevent leaks.
• Keeps water, suds and laundry inside the drum during wash and spin cycles.
• Helps reduce odors and mold buildup when intact and properly sealed.
• Restores proper door closure alignment when the original bellows is damaged.

• One bellows.

• Inspect the tub, door frame and retaining clamp for damage before installation; replace any broken retainers.
• Installation may require removing the door trim and loosening a retaining spring or clamp; follow the washer's service manual.
• Disconnect power and water supply and drain the washer before starting any repairs.

This tub clamp secures the washer tub assembly or related hoses to keep components aligned and reduce movement during operation. It helps restore proper fitment so the tub stays stable and functions quietly. What it does:

• Holds the tub or tub-related components in place to prevent shifting during cycles
• Helps reduce vibration and noise caused by loose tub mounting
• Maintains correct alignment of hoses and seals to reduce leak risk
• Used when a worn or broken clamp allows excessive tub movement

• One tub clamp

• Turn off power and water supply before beginning any repair
• Inspect surrounding components (hose, seal, mounting points) and replace if damaged
• Use common hand tools; secure clamp evenly to avoid twisting the tub or hoses

This multi-connector wiring harness routes power and signals between components to restore electrical connections in the appliance. It replaces a damaged or worn harness to help re-establish reliable component communication and operation. What it does:

• Provides multiple pre-terminated connectors to link control boards, sensors, motors or other modules
• Replaces frayed, burned or broken wiring that can cause intermittent operation or component failures
• Restores proper electrical pathways so affected circuits can function normally
• Helps correct symptoms such as no-start, erratic cycles, or loss of specific functions tied to a failed harness

• One multi-connector wiring harness as shown

• Disconnect power before starting any repair to avoid shock or short circuits
• Match connector shapes and wire colors; do not force connectors together
• Inspect mating connectors and terminals for damage and clean before connecting
• Secure harness to prevent rubbing or pinching during operation