Wm2277hs Parts

Includes sensor probe

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This lifter assembly is the drum baffle inside the washer's inner tub. It lifts and tumbles laundry as the basket turns—replacing a cracked or missing lifter restores proper turnover, helps prevent fabric damage, and quiets thumping noises.

• Provides the lift/turn action that moves clothes through water and detergent
• Helps distribute loads to reduce tangling and improve cleaning results
• A loose, broken, or missing baffle can cause rattling or scraping noises
• Damage can lead to poor turnover or fabric snagging

• Disconnect power before servicing; wear gloves—the inner drum edges can be sharp
• Access from the drum opening; remove the old lifter by releasing tabs or removing screws (varies by model)
• Align the new lifter with the inner-tub slots, lock tabs in place, and secure as designed
• Verify all baffles are firmly attached before running a test cycle

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.

Locking pin for shock absorber.

This is a replacement single electrical harness that restores the factory wiring connection between components. It provides a like-for-like connection to help return affected functions to normal operation when wiring is damaged. What it does:

• Carries electrical signals/power between components and the appliance control circuits
• Replaces frayed, melted, or broken wiring that can cause intermittent or complete function failure
• Commonly used when a component has no power, a circuit is open, or functions stop responding
• Helps eliminate loose connector issues that cause intermittent operation or error codes

• One (1) single electrical harness (part 6877ER3003C)

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shapes and pin counts; do not force connectors—verify secure seating
• Route and secure the harness per factory paths and clips to prevent chafing or heat exposure
• If you see melted connectors, burned insulation, or repeated failures,

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This pump hose routes washer tub water to the drain pump, helping remove wash water during the drain cycle. Replace a cracked or clogged hose to stop leaks and restore normal draining. What it does:

• Channels tub water to the drain pump so the washer can expel water during drain/spin cycles.
• A worn or cracked hose can cause water leaks under the machine.
• Blocked or collapsed hoses can contribute to slow or incomplete draining.
• Compatible replacement for the OEM pump hose connection on qualifying LG washers.

• One pump hose (single hose as shown)

• Disconnect power and turn off water supply before beginning any repairs.
• Confirm correct routing and secure clamps when installing to prevent leaks.
• Inspect adjacent clamps and fittings for wear; replace if corroded or damaged.

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle