Wm2277hw Serial Parts

This is a replacement single electrical harness that restores the factory wiring connection between components. It provides a like-for-like connection to help return affected functions to normal operation when wiring is damaged. What it does:

• Carries electrical signals/power between components and the appliance control circuits
• Replaces frayed, melted, or broken wiring that can cause intermittent or complete function failure
• Commonly used when a component has no power, a circuit is open, or functions stop responding
• Helps eliminate loose connector issues that cause intermittent operation or error codes

• One (1) single electrical harness (part 6877ER3003C)

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shapes and pin counts; do not force connectors—verify secure seating
• Route and secure the harness per factory paths and clips to prevent chafing or heat exposure
• If you see melted connectors, burned insulation, or repeated failures,

This inner door frame is the interior support trim that helps secure the door assembly and provides a finished surface inside the appliance door. It restores proper fit and a clean appearance when the original frame is cracked or damaged. What it does:

• Provides structural support for the inner door panel and helps hold components and liners in place
• Restores proper alignment so the door closes evenly and seals correctly
• Replaces cracked, warped, or broken frame sections that can allow rattling or gaps
• Helps maintain the correct interface between the door and the gasket to prevent airflow issues

• Disconnect power to the appliance before beginning any repairs.
• Removal typically requires taking off the door trim or liner and using basic hand tools; keep fasteners organized.
• Handle the frame and door panels carefully to avoid scratching or bending other surfaces.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

This accessory assembly is a genuine replacement component that restores the appliance's accessory fit and function. It installs in the accessory area to secure and connect related parts for reliable operation. What it does:

• Replaces a damaged or missing accessory assembly to restore proper attachment and alignment
• Secures accessory components so controls and moving parts operate smoothly
• Commonly used when accessories are loose, broken, or no longer seating correctly
• Helps prevent rattling, misalignment, or intermittent accessory-related issues

• Disconnect power (and water, if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for exact steps
• Keep fasteners and small parts organized during removal and reassembly

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

The Shipping Bolt is an OEM part for LG washing machines, designed to secure the washing machine's drum during transportation. These bolts are important for preventing damage to the drum and suspension system by immobilizing the drum, thereby avoiding any excessive movement or vibrations that could occur while moving the appliance. 

Causes of a bad shipping bolt can include improper removal during installation, damage from handling, or degradation over time if it was left in place during operation. A damaged or missing shipping bolt can lead to issues with the washing machine's drum alignment and overall stability.

Symptoms that indicate the shipping bolts need removal or installation include:

• Excessive noise or vibrations during operation, suggesting the bolts were not removed after installation.
• Damage to the washing machine's drum or suspension system after moving the appliance without the bolts properly installed.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Air Chamber is an OEM part for LG washing machines. This part connects to the pressure switch and ensures the washer machine fills with the correct amount of water for the selected cycle. 

Causes of a bad  Air Chamber can include clogging due to detergent residue or debris, cracks or perforations that lead to air leaks, and aging of the material, which might compromise its integrity and function.

Symptoms of a faulty Air Chamber include:

• Inaccurate water level readings leading to overfilling or insufficient water during cycles
• Unusual noises during the fill cycle, indicating air escaping
• The washing machine failing to start the wash cycle due to improper water level detection
• Error codes displayed on the machine that relate to water level issues

This OEM LG part is also compatible with some Kenmore models.

Includes sensor probe

Restore stable, level support with this replacement leg assembly. The adjustable foot steadies the unit on uneven floors, reducing vibration and rattling while allowing precise leveling for proper alignment and smooth, reliable operation.

• Provides adjustable support at the base of the unit
• Helps keep the appliance level on uneven or sloped floors
• Reduces wobble, vibration, and rattling noises
• Promotes proper door alignment and closure
• Replaces stripped, cracked, or missing leg assemblies

• Disconnect power; shut off water supply if applicable
• Carefully tilt and support the appliance to access the leg area
• Unthread the old leg; hand-thread the new assembly to avoid cross-threading, then fine-adjust with a wrench
• Level front-to-back and side-to-side; confirm stability before use

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn