Wm2277hw Serial Parts

This cover cap is a small plug that snaps into an open hole on the washer's cabinet or panel. Replace a missing or damaged cap to restore a finished appearance and help keep dust, lint, and splashes out of the enclosure.

• Closes an unused hole on the appliance panel to maintain a sealed cabinet
• Helps keep debris and moisture from entering the machine
• Restores the clean, finished look of the unit
• Typical signs it's needed: missing cap, cracked or loose cap, or a visible open hole on the panel

• Disconnect power and water supply before servicing the appliance
• Align the cap with the hole and press straight in until fully seated
• No tools are typically required; avoid prying on painted surfaces
• Do not block any ventilation or drain openings—install only in the designated capped hole

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.

Locking pin for shock absorber.

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle

This frame assembly is the outer trim piece that restores the appliance's finished appearance and helps hold adjacent panels or components in place. It replaces damaged or missing trim to improve fit and seal. What it does:

• Provides a finished edge and structural support for the appliance front or access panel
• Helps keep adjacent panels aligned and reduces gaps where dirt or moisture can enter
• Restores proper mounting points for switches, bezels, or door panels when the original is cracked or broken
• Commonly replaced for visible damage, warped trim, or when the frame no longer secures nearby components

• One frame assembly

• Disconnect power before starting and remove any connected water lines if applicable
• Handle trim carefully to avoid scratching the finish and to prevent personal injury from sharp edges
• Installation typically requires removing outer panels and fastening the frame with existing screws or clips; keep removed hardware for reassembly

The LG Door Hinge Assembly is an essential component of LG washers. This OEM replacement part is specifically designed to ensure the smooth and secure operation of the washer's door. The hinge assembly is responsible for connecting the door to the main body of the appliance, allowing easy access to the washing drum. It provides stability and durability to the door, enabling it to open and close effectively during the washing and loading processes.

This part fixes the following symptoms:

• Difficulty in opening or closing the washer door
• Door sagging or misalignment
• Excessive noise or squeaking when operating the door
• The door not staying securely closed during washing cycles
• Visible damage or wear on the hinge assembly