Wm3370hwa Parts

This connector hose replaces the appliance's water connection to restore secure water flow and reduce the risk of leaks or interrupted dispenser/ice-maker operation. It's a direct replacement for a damaged or leaking supply connector. What it does:

• Connects the household water supply to the appliance's internal water valve or dispenser.
• Restores reliable water flow when a cracked, split, or collapsed hose prevents proper delivery.
• Reduces water leakage caused by worn or damaged connector ends and seals.
• Commonly needed when you see visible leaks, no water to the dispenser/ice maker, or a loose/broken hose connection.

• Turn off water supply and unplug the appliance before replacing the hose to avoid electric shock or water damage.
• Use proper clamps and fittings; make sure connections are seated and tightened just enough to stop leaks—do not overtighten.
• After installation, restore power and water, then check all connections carefully for leaks. Replace immediately if the hose or fittings show signs of damage.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Power Cord Assembly is an OEM replacement part for LG front-loading washing machines. As the primary connection to household electricity, this cord safely delivers the required voltages to internal components.

Causes of a damaged or defective cord typically involve accidental cuts, abrasions or punctures accumulated over time. Repeated bending stresses during installations can prematurely crack insulation as well.

Symptoms of a problematic power cord include: 

• Inability to power "On" when plugged in  
• Tripped breakers or ground fault outlets
• Visible wire fraying or other signs of compromised integrity

This OEM assembly fits some Kenmore/Sears machines and protects against potential shock or fire hazards.

This hinge spring restores proper door tension so the appliance door opens and closes smoothly and stays in position. Replacing a worn spring reduces sagging, uneven closing, and noisy or slamming doors. What it does:

• Provides tension at the hinge to hold door position and improve alignment
• Helps prevent door sagging and uneven gaps caused by worn springs
• Reduces slamming, popping, or grinding sounds during door movement
• Common symptom: door won't stay open/closed or feels loose at the hinge

• Disconnect power and unplug the appliance before starting any repair
• Support the door while removing/installing the spring to prevent it from dropping
• Basic hand tools (screwdriver, pliers) are typically needed; follow the appliance's service guide

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This drawer front assembly replaces a damaged or worn front panel to restore the appliance's appearance and proper drawer operation. It fits the specified LG drawer system and provides the finished exterior surface the drawer needs. What it does:

• Replaces the drawer front panel to restore proper drawer alignment and cosmetic appearance
• Provides a secure mounting surface for the drawer face and any attached trim or handle
• Helps stop rubbing, sticking, or misalignment caused by a cracked or warped front panel
• Restores a uniform exterior look when the original drawer front is dented, scratched, or broken

• One Drawer Panel Assembly (front panel) as shown

• Basic removal of the drawer and a few fasteners is usually required; keep hardware for reuse unless damaged
• Handle or trim may need to be transferred if not integrated; fit before final fastening
• Power off and empty the drawer before beginning work to avoid injury or damage

This complete door assembly replaces a damaged or broken front door to restore safe access and proper sealing. It provides the exterior door surface and mounting points so the appliance closes and operates as intended. What it does:

• Replaces a cracked, dented, or warped door that prevents proper closure
• Provides the door surface and mounting/latch area required for proper sealing
• Restores a solid, secure closing action so the appliance can run normally
• Helps eliminate gaps that can allow heat, moisture, or noise to escape
• Covers and protects internal components behind the door

• Disconnect power and water before starting any repair
• Handle carefully to avoid injury from sharp edges or glass; wear gloves
• May require removal of trim or screws and alignment of hinge pins during installation