Wm377cw Parts

This washer drum lifter (baffle) mounts inside the drum to raise and tumble clothes as the basket turns. Replace a cracked or missing lifter to restore wash action, help protect fabrics, and reduce rattling noises.

• Attaches to the inner drum and lifts garments during rotation for effective tumbling
• Helps distribute loads and improve mechanical cleaning action
• Direct replacement for lifters that are cracked, loose, sharp-edged, or missing
• Typical symptoms: poor tumbling/wash results, thumping or rattling from the drum, clothing snags or tears, lifter wobbling or fallen off

• Disconnect power and turn off water supply before servicing
• Open the door and rotate the drum to access the lifter
• Depending on model, release locking tabs from inside the drum or remove the retaining fastener; align and secure the new lifter
• Ensure the lifter is fully seated and secure; run a short rinse/spin to verify proper operation

Customized machine screw for select washers that fastens specific assemblies and resists vibration. Replace a missing, stripped, or damaged factory screw to restore a solid, rattle-free fit and proper component alignment.

• Secures designated brackets, panels, or housings per the manufacturer's specifications
• Maintains alignment and stability under high-speed spin and vibration
• Replaces missing, corroded, or stripped hardware to stop looseness and noise
• Use when the original screw is worn, damaged, or lost

• Unplug the appliance and shut off water before servicing
• Support the component while removing/installing screws
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep screws organized—lengths and styles may vary by location

This Cover Cap replaces a missing or damaged cosmetic cap to restore a clean finished appearance and help protect underlying fasteners and openings from dirt. It's a simple, low-cost fix for visible damage. What it does:

• Covers and conceals exposed screw heads, fastener holes, or trim openings for a finished look
• Helps limit dirt and debris accumulation in small openings
• Useful when the original cap is cracked, broken, or lost
• Restores appliance aesthetics without replacing larger panels

• High-level: typically snaps or presses into place; may require removing the adjacent trim or panel for access
• Disconnect power and water (if applicable) before removing panels to avoid electrical or water hazards
• Use gentle prying with a plastic trim tool to avoid scratching surrounding surfaces

This multi-connector wiring harness routes power and control signals between internal components for reliable appliance operation. Replacing a damaged harness restores secure electrical connections and helps resolve intermittent or lost-function symptoms. What it does:

• Links control board and internal components using multiple connector plugs for correct signal and power distribution.
• Commonly replaced for intermittent operation, loss of specific functions, or visible damaged/burned wiring.
• Ensures connector-to-connector fit to prevent loose connections and arcing that can cause faults.
• Works as a direct replacement harness where the original wiring assembly is damaged or connectors are worn.

• Disconnect power (unplug or turn off circuit breaker) before accessing internal wiring.
• Note connector positions and routing before removal; swap one connector at a time to avoid miswiring.
• Do not force connectors; align pins and push until fully seated. Replace any damaged retaining clips.
• After installation, restore power and test all functions before reassembling panels.

A replacement balance weight that helps stabilize the washer drum during spin cycles to reduce vibration and noise. Restores proper weight distribution so the washer runs more quietly and reliably. What it does:

• Counters drum imbalance to reduce shaking and excessive movement during spins
• Helps minimize noise caused by uneven loads
• Preserves drivetrain components by reducing stress from heavy vibration
• Supports consistent spin performance and load stability

• Disconnect power and water supply before starting any repairs
• Handle carefully—weights can be heavy and require a helper or proper lifting technique
• Follow the washer's service manual for mounting location, orientation, and fastener torque
• After installation, run a test spin with a small load to reduce vibration

This connector hose replaces the appliance's water connection to restore secure water flow and reduce the risk of leaks or interrupted dispenser/ice-maker operation. It's a direct replacement for a damaged or leaking supply connector. What it does:

• Connects the household water supply to the appliance's internal water valve or dispenser.
• Restores reliable water flow when a cracked, split, or collapsed hose prevents proper delivery.
• Reduces water leakage caused by worn or damaged connector ends and seals.
• Commonly needed when you see visible leaks, no water to the dispenser/ice maker, or a loose/broken hose connection.

• Turn off water supply and unplug the appliance before replacing the hose to avoid electric shock or water damage.
• Use proper clamps and fittings; make sure connections are seated and tightened just enough to stop leaks—do not overtighten.
• After installation, restore power and water, then check all connections carefully for leaks. Replace immediately if the hose or fittings show signs of damage.

This multi wiring harness connects control circuitry to multiple components, restoring reliable electrical pathways for proper operation. It replaces a damaged or frayed harness to help eliminate intermittent power, unresponsive controls, or component failures caused by wiring faults. What it does

• Routes power and signals between the control board and several appliance components.
• Re-establishes secure electrical connections when original wires are broken, burnt, or corroded.
• Can address symptoms such as intermittent operation, components not receiving power, or erratic behavior tied to wiring faults.
• Uses OEM-style connectors and wiring lengths to match factory routing for a proper fit.

• One multi wiring harness as shown

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Handle connectors by the housings—do not pull on wires—and ensure all plugs fully seat with audible clicks.
• Route the harness following original wire paths and secure with existing clips or ties to prevent contact with moving or hot parts.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:

• Replaces a worn, cracked, or missing control knob to regain safe, predictable control
• Engages the shaft and detents so settings stay put during use
• Helps eliminate slipping or difficulty turning the control
• Matches original fit and function for direct replacement

• One knob assembly as shown

• Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
• Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
• Wear work gloves to protect hands from sharp edges during access

This holder assembly secures and positions internal components so the appliance's parts stay aligned and operate smoothly. Replacing a worn or broken holder helps stop rattling and restores proper fit where parts connect. What it does:

• Supports and locates adjacent components to maintain correct alignment
• Prevents excess movement that can cause noise or wear
• Helps ensure proper engagement of the associated trim or functional part
• Common symptom: loose, rattling, or misaligned components near the mounting area

• Designed to replace the original holder; fit with the part number before ordering
• Basic hand tools required; access panel removal may be necessary
• Disconnect power before beginning service to avoid shock or injury
• If clips or screws are damaged, replace them with equivalent hardware for a secure fit

The Power Cord Assembly is an OEM replacement part for LG front-loading washing machines. As the primary connection to household electricity, this cord safely delivers the required voltages to internal components.

Causes of a damaged or defective cord typically involve accidental cuts, abrasions or punctures accumulated over time. Repeated bending stresses during installations can prematurely crack insulation as well.

Symptoms of a problematic power cord include: 

• Inability to power "On" when plugged in  
• Tripped breakers or ground fault outlets
• Visible wire fraying or other signs of compromised integrity

This OEM assembly fits some Kenmore/Sears machines and protects against potential shock or fire hazards.

The Display PCB Assembly is an OEM component specifically designed for LG front-loading washing machines. Located within the control panel, this printed circuit board coordinates interactions between users and the washer’s electronic components. Precise microchip programming processes commands to display cycles and temperature settings.   

Causes of a bad display PCB can include water damage corroding circuits over time, power surges damaging microchips, or loose connections inhibiting full communication between the display and washer’s systems. Without a properly functioning interface board, homeowners cannot efficiently operate cycles and settings.

Symptoms of a bad display PCB include:

• Dim or unresponsive touch controls and LED displays  
• Stuck buttons that do not accept selection input
• Erratic warning beeps or tones within the washer cabinet
• Inability to select or advance desired cycles 

This LG OEM replacement ensures consistent laundry control performance. Compatible also with Kenmore front-loaders, it offers convenient repair through a seamless fit. 

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This hose connector joins the water inlet hose to the appliance, restoring a secure, watertight feed for normal fill and wash cycles. Replaces a worn or damaged connection to stop leaks and ensure proper water flow. What it does:

• Connects the incoming water hose to the appliance inlet for stable water delivery
• Stops leaks caused by cracked, split, or loose connector fittings
• Helps restore normal fill behavior when a failed connector is preventing proper water flow
• Serves as a direct replacement for a damaged or corroded inlet connection

• Turn off and shut off the home's water supply and unplug the appliance before installing
• Remove the old connector and clean mating surfaces; inspect hose and clamps for wear
• Hand-start fasteners, then snug fittings—avoid over-tightening to prevent damage

This lifter is a replacement drawer support that helps hold and guide a refrigerator/freezer drawer for smooth, even operation. Restores proper alignment and reduces sticking or uneven movement. What it does:

• Supports and stabilizes a sliding drawer so it opens and closes smoothly
• Helps maintain proper drawer alignment and load distribution
• Worn or broken lifters can cause sagging, binding, or uneven drawer movement
• Replaces damaged or missing lifter hardware to restore normal drawer function

• Disconnect power and empty the drawer before starting any repair
• Remove the drawer or access panel per your model's service instructions to reach the lifter
• Install the new lifter in the same orientation and secure any retaining clips or screws; do not force parts into place
• If fasteners or adjacent guides are damaged, replace them as well for a secure fit