Wrf757sh Parts

This shaft is the replacement rotating shaft used to support and align the appliance drum or tub, restoring smooth rotation and reducing noise from worn or damaged drive components. What it does:

• Provides a stable mounting point for the drum/tub to rotate smoothly
• Transfers rotational motion and helps maintain drum alignment
• Prevents wobble and uneven wear caused by a damaged shaft
• Commonly replaces a worn or noisy shaft that causes grinding, scraping, or rough drum rotation

• Disconnect power to the appliance before starting any repair
• Some disassembly of the cabinet and drum/tub is required
• Inspect related rollers, bearings, seals and fasteners; replace any worn components to prevent repeat failure
• Use appropriate tools and safety gear

The Evaporator Fan Grommet is an OEM component specifically designed for Whirlpool refrigerators. Found along the rear wall of the fridge compartment where the evaporator fan motor is located, the evaporator fan grommet serves an important sealing function.

Constructed of flexible rubber, the evaporator fan grommet forms a tight, airtight seal around the electrical wiring harness and ventilation ductwork attached to the rear-mounted evaporator fan motor. This helps prevent the escape of cold air from the refrigeration system and allows the evaporator fan motor to work efficiently. 

Causes of a bad evaporator fan grommet include cracks or splits from vibration stress over years of use. Dried-out seals no longer achieving a tight fit is also possible. 

Symptoms of a bad evaporator fan grommet include:

• Cold air leaking from around the rear wall area  
• Increased humidity inside the fridge compartment
• Decreased cooling performance efficiency

Compatible with Whirlpool, KitchenAid, Jenn-Air, and select Kenmore side-by-side models.

The Pan-Drip is an OEM part for Whirlpool refrigerators. It is designed to collect and manage condensation and any water that may drip inside the refrigerator, preventing it from pooling at the bottom of the appliance. This pan measures approximately 20 inches by 16 inches with a 2-inch depth.

Causes of a bad pan-drip can include wear and tear over time, cracks or breaks due to impact, and buildup of dirt or debris that can block proper drainage. When the pan-drip fails, it can lead to water accumulation and potential leaks.

Symptoms of a bad Pan-Drip include:

• Water pooling inside the refrigerator
• Leaks from the bottom of the refrigerator
• Visible cracks or damage to the pan
• Mold or mildew buildup due to improper drainage

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Stainless

The Door Handle is an OEM part for Whirlpool refrigerators. It provides an ergonomic grip that allows for easy opening and closing of the refrigerator door. The handle bears the inward force across the door to deliver smooth operation with each use.

Causes of a bad door handle can include cracks, breaks or wear to the plastic over time due to repeated opening/closing motions. Physical damage from impact is also a possible cause of handle failure.

Symptoms of a bad door handle include:

• The handle no longer securely holds the door closed
• Difficulty opening the door without the handle assistance
• Cracks or breaks visible in the plastic
• Loose, sagging or misaligned handle placement

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Inverter Box is an OEM component specifically designed for Whirlpool French door refrigerators. Located inside the refrigerator compartment top behind removable panels, the inverter box houses electronic components that control the compressor motor and refrigeration systems.

Causes of a bad inverter box include failure of internal circuit boards over several years of regulating refrigeration cycles or damage from liquid spills inside the unit.  

Symptoms of a bad inverter box include:

• Failure of the refrigerator section to adequately cool and maintain temperatures
• Erratic fluctuations in cold air dispensing from vents     
• Repeated triggering of defrosting modes unnecessarily 
• Inability to regulate between freezer and refrigerator settings

This Whirlpool replacement part is compatible with Maytag, Jenn-Air, Amana, Magic Chef, and Kenmore side-by-side refrigerators.
 

This crisper drawer roller guide mounts to the refrigerator shelf/frame and forms the track the drawer's roller rides in. Replacing a worn guide restores smooth, aligned drawer movement and helps prevent the crisper from sticking or coming off track.

• Guides and supports the crisper drawer roller to keep the drawer on its track
• Helps the drawer open and close smoothly and evenly
• Common symptoms of a failed guide: drawer sticks, tilts, wobbles, or pops off track
• Physical damage or wear to the guide can impede drawer travel

• Disconnect power and remove the crisper drawer and shelf/glass for access.
• Locate the damaged guide; release its locking tabs or remove the retaining screw(s).
• Align the new guide in the same orientation and secure it without overtightening.
• Reinstall the shelf and drawer; verify smooth drawer operation.

The Heater is an OEM part for Whirlpool refrigerators. It is a thin heating element located behind the cover for the ice compartment inside the fresh food section that functions to prevent condensation from accumulating.

Causes of a bad heater can include failure of the heating element over many cycles of use, cracks or breaks due to normal wear and tear or repeated door opening/closing stress.

Symptoms of a bad heater include:

• Foggy or clouded refrigerator door panels
• Visible condensation building up inside refrigerator doors
• Potential for water droplets or leaks inside door panels

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement screw fastens appliance panels and components securely. Replace a missing, stripped, or corroded original to restore a tight fit and help prevent rattling, vibration, and gradual loosening of assemblies.

• Secures panels, brackets, and internal assemblies to the frame
• Replaces damaged or missing hardware to maintain proper fit
• Helps reduce vibration, noise, and movement caused by loose parts
• Supports correct alignment at the original mounting points

• Disconnect power and shut off water or gas before service.
• Match the original screw's location and length; replace one at a time if needed.
• Use the correct driver/bit and avoid overtightening to prevent stripping plastic or metal.
• Reuse any washers or clips only if in good condition.

This condenser fan blade moves air across the refrigerator's condenser coil and compressor to remove heat, helping the unit cool efficiently. Replace a cracked, warped, or loose blade to restore proper airflow and reduce noise.

• Circulates air through the condenser section to dissipate heat from the refrigerant
• Supports stable fridge and freezer temperatures and efficient compressor operation
• Common symptoms: rattling/scraping noises, weak or no airflow at the rear/bottom, longer run times, or warming compartments
• Replace if the blade is cracked, warped, wobbling, or loose on the motor shaft

• Disconnect power and pull the refrigerator away from the wall; remove the rear access panel to reach the condenser fan
• Note the original blade orientation/rotation; remove the old blade from the motor shaft (release any retainer if present)
• Press the new blade onto the shaft until fully seated; ensure it spins freely with proper clearance and airflow direction
• Reinstall the panel, restore power, and verify normal airflow and sound

This rubber grommet cushions and seals a wiring, hose, or shaft opening to help prevent abrasion, reduce vibration, and maintain a snug fit for quieter, safer appliance operation. What it does:

• Protects wiring, hoses, or moving shafts from chafing and wear
• Helps seal openings to limit water, air, or lint intrusion
• Dampens vibration and reduces noise where panels or components meet
• Worn or damaged grommets can cause rubbing sounds, visible wear, loose hoses, or leaks

• Disconnect power (and water if applicable) before beginning any repair
• Push-fit replacement in most applications; a small screwdriver or needle-nose pliers can help with removal or alignment
• Inspect surrounding seals, hoses, and mounting surfaces and replace damaged parts as needed

Drip tray that catches defrost and condensation water to prevent leaks and floor damage. Replaces a cracked or missing tray to restore proper water collection and reduce standing water beneath the appliance. What it does:

• Collects melted frost and condensation from the cooling system so water is contained and managed.
• Channels water toward the appliance's evaporation/drain area so it can evaporate safely.
• Helps prevent puddles and potential floor damage caused by a damaged or missing tray.
• Replace when tray is cracked, warped, leaking, or shows visible damage.

• Disconnect power to the appliance before performing any service.
• Access is typically through the lower toe grille or a rear access panel.
• Inspect mounting tabs and surrounding supports for damage and ensure the new tray seats properly.
• Wear gloves and take care around sharp sheet-metal edges during removal/install.

This replacement door shelf bin restores usable storage on the refrigerator door so bottles, jars and condiments stay organized and secure. Swap a cracked, broken or loose bin to prevent items from falling and reduce spills. What it does:

• Provides a sturdy storage shelf that mounts to the refrigerator door for bottles, jars and small items.
• Keeps door contents secure during normal opening and closing of the door.
• Replaces cracked, warped or otherwise damaged bins that no longer hold items or stay seated.
• Helps prevent spills and lost items caused by a broken or loose door bin.

• Empty the door bin before removal to avoid dropping items or injury.
• On most models lift the bin slightly and pull straight out; to install, align the mounting tabs and press straight in until it seats.
• No special tools are typically required; handle carefully to avoid cracking the replacement.
• If the bin won't seat or retaining clips are damaged, inspect and replace the clips or supports as needed.

The Dual Evaporator Assembly is an OEM part for Whirlpool refrigerators. Found within the refrigerator cabinet behind the sidewalls, these dual evaporator coils absorb heat from the refrigerated air and help maintain the optimal cold temperatures needed in each section. 

Symptoms of a bad dual evaporator assembly include:

• Fluctuating or inadequate temperatures in both freezer and fresh food sections
• Frost or ice buildup inside cabinets  
• Increased humidity levels allowing food to spoil faster

Causes can be normal component wear over time, damage to coils from falls/impacts within the refrigerator, or refrigerant leaks decreasing cooling ability. 

This OEM replacement part is also compatible with refrigerator models from brands including Maytag, Jenn-Air, Amana, Magic Chef, and some Kenmore units.

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.