Wrt31fzdw02 Parts

This washer is a small hardware spacer used in appliance assemblies to distribute load and maintain proper spacing under a fastener or rotating component. Replacing a worn or missing washer helps restore alignment, reduce noise, and keep parts secure.

• Distributes fastener load to protect mating surfaces
• Maintains spacing/alignment between components
• Can act as a thrust surface to reduce friction and wear
• Typical symptoms: looseness or wobble, scraping/squeaking noises, or parts that won't stay tight

• Disconnect power; shut off gas and/or water as applicable
• Note the order/orientation of washers, spacers, and clips during disassembly; take a photo for reference
• Inspect related parts (retainers, bushings) and replace if worn
• Tighten fasteners per manufacturer guidance; avoid overtightening and verify smooth operation after reassembly

Color: Black

This burner orifice meters the gas delivered to a burner so you get a stable, properly sized flame. Replacing a clogged or damaged orifice helps restore quick ignition, consistent flame quality, and even heating on gas appliances.

• Meters gas flow from the valve to the burner for correct flame size and shape
• Helps maintain efficient, even heating and clean combustion
• Wear or blockage may show as delayed or no ignition, weak/uneven flame, or yellow tipping
• Can reduce popping or flare-ups caused by improper gas metering

• Shut off gas supply and disconnect power before servicing
• Remove the old orifice with the proper wrench/nut driver; install the new one snugly—do not overtighten
• After reassembly, leak-check connections and verify flame; adjust air shutter only if specified by the service manual

The Icemaker is an OEM part for Whirlpool refrigerators. It automatically produces batches of ice using a water inlet and freeze cycle.

Causes can be failures in the temperature probe, water valve, ejection mechanism, or freezing compartment. Mineral buildup from hard water reduces efficiency over many harvest cycles as well.

Symptoms of a bad ice maker include:

• No ice production or low ice yields over time
• Ice cubes appearing cloudy or improperly formed
• Leaking or dripping water inside the freezer
• Clicking or grinding noises during operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: white. It measures about 1 inch in diameter.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

This replacement light bulb restores clear, dependable illumination so you can easily see inside your appliance and check status at a glance. Replacing a burned-out or dim lamp improves visibility, convenience, and day-to-day safety.

• Provides light when the door opens or the light switch is turned on
• Helps you view contents and monitor progress without guesswork
• Addresses no-light, dim, or flickering conditions
• Installs in the designated light socket on compatible models

• Disconnect power to the appliance before servicing
• Allow the bulb and surrounding area to cool completely
• Handle glass with a clean cloth or gloves; skin oils can shorten bulb life
• Install gently without overtightening; use only the type/rating specified for your model

This hinge cover replaces a damaged or missing hinge trim to protect and conceal the hinge assembly and restore the appliance's finished appearance. It fits over the hinge area and helps reduce dirt buildup and exposed hardware. What it does:

• Covers and protects hinge hardware, hiding screws and sharp edges
• Helps keep dirt, lint, and moisture out of the hinge area
• Restores the appliance's original, finished look
• Common symptoms: cracked, broken, or missing cover; exposed hinge hardware; cosmetic damage or debris buildup

• Refer to your model diagram for correct orientation and fastener locations
• Basic hand tools may be required; some models need the hinge loosened or partially removed
• Disconnect power and/or unplug the appliance before starting work when applicable
• Handle edges carefully to avoid cuts; follow OEM instructions for reassembly

This thermistor cover shields and positions the refrigerator's temperature sensor so it reads cabinet air accurately. Replacing a cracked or missing cover helps restore stable temperatures and normal cooling performance.

• Holds the thermistor in place and shields it from direct airflow for accurate temperature sensing
• Helps prevent erratic temperatures, overcooling/undercooling, or long run times caused by an exposed sensor
• Commonly replaced when the original cover is cracked, loose, or missing
• Supports consistent temperature control by ensuring proper sensor placement

• Disconnect power before servicing
• Remove shelves/bins as needed to access the sensor location
• Align the thermistor and seat the cover fully; engage tabs or reuse existing hardware per model
• Avoid pinching the sensor or wiring and verify the cover is snug

This leveler is the adjustable foot that threads into the base to stabilize and level the appliance. Proper leveling reduces rocking and vibration and helps doors, drawers, or tubs align and operate smoothly.

• Supports the appliance and allows height adjustment to compensate for uneven floors
• Helps prevent rocking, rattling, or excessive vibration during use
• Aids in proper door/lid alignment and smooth closing
• Replace if the foot is cracked, stripped, or missing

• Disconnect power; turn off gas or water supply if applicable
• With a helper, carefully tilt or raise the appliance and protect the floor
• Unthread the old leveler; hand-thread the new leveler to avoid cross-threading, then tighten as designed
• Adjust to level side-to-side and front-to-back; the unit sits stable on all corners

The Air Duct is an OEM part for Whirlpool refrigerators. It is a component that directs cool air throughout the appliance. The air duct is designed to channel air from the freezer section to the fresh food section.

Causes of a bad air duct can include cracks or fractures in the ducting material, damage to air vents or directional fins, or blockages that disrupt proper air flow.

Symptoms of a bad air duct include:

• Inconsistent or uneven interior temperatures
• Longer cool down times after door openings
• Frost or condensation issues in problem areas
• Portions of refrigerator not maintaining proper temperatures

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

A replacement hinge pin that secures and guides the appliance door hinge so the door opens, closes and stays aligned. Installs quickly to restore correct door pivot and reduce sag or binding. What it does

• Acts as the pivot point for the door hinge so the door swings smoothly.
• Restores proper door alignment to prevent gaps or doors that won't latch fully.
• Stops noisy or rough door movement caused by a worn or bent pin.
• Helps maintain seal performance by keeping the door flush with the cabinet.

• Disconnect power to the appliance and remove any items from the door area before starting.
• Support the door while removing/installing the pin to avoid damage or injury.
• Use appropriate hand tools and keep track of any retainers or fasteners removed.

This replacement glass shelf panel restores a stable, easy-to-clean storage surface inside your refrigerator when the original is cracked, missing, or stained—helping contain minor spills and letting you use your shelf space with confidence. What it does:

• Replaces damaged or missing shelf glass to maintain a flat, sturdy surface for food storage
• Helps contain small spills to the shelf area for easier cleanup
• Fits into the existing shelf frame or rests on factory support rails as designed
• Common symptoms include visible cracks or chips, shelf won't sit level, or lost/limited storage space

• 1 glass shelf panel

• Remove all items and the shelf/frame from the refrigerator before swapping the glass
• Handle glass with two hands; wear cut-resistant gloves and eye protection
• Align carefully and seat fully in the frame or on support ledges before reloading
• Disconnect power if working near moving parts or wiring; work on a cool appliance

Color: Grey

The Handle End Cap is an OEM part for Whirlpool refrigerators. It covers and protects the end of the refrigerator's door handle.

A bad door handle end cap can be caused by regular wear and tear, accidental damage, or exposure to harsh cleaning chemicals. If you notice cracks, discoloration, or a loose fit of the end cap on your refrigerator's door handle, it may indicate a problem with the cap itself.

Symptoms of a bad door handle end cap include:

• Cracked or damaged 
• Discoloration or fading 
• Loose or wobbly fit on the handle

Replace your faulty door handle end cap with this genuine OEM part to restore your refrigerator's handle. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This meat pan holder is the under-shelf support that guides the deli/meat drawer. Replacing a cracked holder restores smooth sliding and keeps the pan level so it doesn't bind, sag, or drop when opening and closing. What it does:

• Supports and guides the deli/meat pan beneath its shelf
• Keeps the drawer aligned and level for smooth operation
• Helps prevent rubbing, sticking, or the drawer falling off its track
• Typical failure signs: cracked plastic, broken mounting tabs, pan tilts or won't slide smoothly

• 1 meat pan holder

• Disconnect power and clear the shelf area for safe access
• Remove the meat pan and the shelf it rides on
• Release the damaged holder and install the new holder in the same orientation and mounting points
• Reinstall the shelf and drawer; verify smooth travel before loading

Size: 8-18 x 1/2 inch.