Wrx7355dbm03 Parts

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn seal helps stop warm air leaks, reduce frost and condensation, and keep temperatures stable for better efficiency and food preservation.

• Creates a continuous perimeter seal between the door and cabinet to prevent air infiltration
• Helps maintain correct temperatures and reduce moisture/frost buildup
• Restores proper door closing when the old gasket is torn, warped, or permanently compressed
• Common symptoms: door not sealing or popping open, condensation around the door, temperature swings, frost along the door edges

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Let the new gasket relax at room temperature or warm it in water to remove kinks
• Pull the old gasket from the door channel; clean the mating surface
• Seat corners first, then press the gasket fully into the channel; use gentle low heat to smooth waves if needed

This replacement screw fastens appliance panels and components securely. Replace a missing, stripped, or corroded original to restore a tight fit and help prevent rattling, vibration, and gradual loosening of assemblies.

• Secures panels, brackets, and internal assemblies to the frame
• Replaces damaged or missing hardware to maintain proper fit
• Helps reduce vibration, noise, and movement caused by loose parts
• Supports correct alignment at the original mounting points

• Disconnect power and shut off water or gas before service.
• Match the original screw's location and length; replace one at a time if needed.
• Use the correct driver/bit and avoid overtightening to prevent stripping plastic or metal.
• Reuse any washers or clips only if in good condition.

This rubber grommet cushions and seals a wiring, hose, or shaft opening to help prevent abrasion, reduce vibration, and maintain a snug fit for quieter, safer appliance operation. What it does:

• Protects wiring, hoses, or moving shafts from chafing and wear
• Helps seal openings to limit water, air, or lint intrusion
• Dampens vibration and reduces noise where panels or components meet
• Worn or damaged grommets can cause rubbing sounds, visible wear, loose hoses, or leaks

• Disconnect power (and water if applicable) before beginning any repair
• Push-fit replacement in most applications; a small screwdriver or needle-nose pliers can help with removal or alignment
• Inspect surrounding seals, hoses, and mounting surfaces and replace damaged parts as needed

The Freezer Drawer Gear Clip is an OEM part for Whirlpool refrigerators. It is designed to secure the gear mechanism that allows the freezer drawer to slide in and out smoothly. This clip ensures that the drawer operates efficiently, providing easy access to the freezer compartment.

Causes of a bad gear clip can include wear and tear from regular use, damage due to overloading the drawer, or breakage from accidental impact. A faulty gear clip can impair the drawer’s movement and make it difficult to open or close properly.

Symptoms of a bad refrigerator freezer drawer gear clip include:

• The freezer drawer not sliding smoothly
• Difficulty in opening or closing the drawer
• The drawer coming off its track
•  Unusual noises during the drawer’s operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Grey (Right Hand)

This door hinge secures and guides the appliance door so it opens and closes smoothly and stays aligned. It replaces a worn or damaged hinge to restore proper door operation and prevent sagging or gaps. What it does:

• Provides pivot support so the door swings smoothly and stays in position
• Keeps the door aligned to form a proper seal when closed
• Prevents sagging, dragging, or uneven closing caused by a broken hinge
• Works as the mechanical connection between the door and cabinet/frame

• One door hinge

• Disconnect power (or unplug the appliance) before starting any repair
• Support the door while removing hinge fasteners to avoid injury or damage
• Use proper tools and tighten fasteners securely; avoid over-tightening

Color: Stainless

The Door Handle is an OEM part for Whirlpool refrigerators. It is a component that facilitates easy access to the fresh food and freezer compartments. The handle interfaces directly with users to open and close refrigerator doors.

Causes of a bad door handle can include wear and tear over time from repeated use, or damage such as cracks, chips or breaks from accidental impact. Temperature fluctuations from frequent door openings can also cause handles to warp or fail prematurely.

Symptoms of a bad refrigerator door handle include:

• Difficulty opening or closing the refrigerator door
• The door not latching securely
• Internal components like springs or cables becoming loose or worn

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement meat pan is a molded deli pan that holds and contains meat and deli items inside the refrigerator drawer, helping prevent spills and keeping foods organized. It restores a clean, stable surface for storing prepared foods. What it does:

• Provides a dedicated tray for deli meats, cheeses and prepared foods
• Catches juices and prevents drips from reaching the refrigerator floor or drawer tracks
• Replaces cracked, warped or stained pans that no longer seal or sit flat
• Helps maintain food organization and easier cleanup

• Slide the new pan into the deli/crumb drawer area until it seats fully; no tools typically required
• Clean the pan before first use and after each use with mild soap and warm water
• Inspect drawer rails and mounts for debris before reinstalling the pan
• For safety, follow refrigerator manufacturer's instructions and disconnect power only if directed by the OEM for related service

This ice bucket and trim assembly replaces the fridge's ice storage container and surrounding trim, restoring secure ice storage and a finished appearance. Designed to collect ice from the icemaker so ice is contained and accessible. What it does:

• Collects and stores ice produced by the refrigerator icemaker.
• Trim secures the bucket in place and helps guide ice toward the dispenser or access area.
• Replaces cracked, broken, or warped buckets that cause ice spills, poor seating, or difficulty removing the bucket.
• Helps prevent loose ice and improves dispenser/door alignment when the original bucket or trim is damaged.

• Disconnect power to the refrigerator and remove stored ice and food from the work area before starting.
• Remove the old bucket per your refrigerator's service or owner manual—lift/tilt or unclip any retaining tabs as required.
• Install the new bucket and align the trim so tabs engage; do not force parts—inspect for proper seating.
• Restore power and run the icemaker/dispenser through a test cycle; discard the first batch of new ice.

Top hinge assembly secures the top of the refrigerator door to the cabinet and restores proper pivoting for smooth opening and correct alignment, helping maintain the door seal and prevent sagging. What it does:

• Supports and pivots the top of the door for stable, even movement.
• Keeps the door aligned so the gasket seals evenly across the cabinet.
• Helps prevent door sagging, rubbing, or uneven gaps that can affect cooling.
• Resolves symptoms like difficulty closing or a door that sits crooked.

• Disconnect power and empty the door before starting the repair.
• Have a second person or a support to hold the door while removing/installing the hinge.
• Use basic hand tools and follow the manufacturer's service instructions; avoid forcing parts.
• After installation, check door alignment and operation to ensure a proper seal.

The Spacer is an OEM component specifically designed for Whirlpool side-by-side refrigerators. Located within refrigerator door walls, it maintains precise alignment between internal insulation and outer door panels.

Causes of a bad spacer include cracks or breaks developing from repeated door openings and closings. Prolonged very low temperatures can also make plastic prone to snapping.

Symptoms of a bad spacer include: 

• Misaligned or loose door walls and panels
• Cold air leakage around the door perimeter
• Difficulty closing doors completely flat
• Visible broken pieces inside door walls

This OEM Whirlpool replacement spacer restores critical door insulation integrity. Its durable construction supports tight door seals to maintain interior climate control.

Replace yours if any issues arise. This part is also compatible with some GE, Crosley, and select Kenmore side-by-side models. Reliable seal performance relies on an OEM spacer replacement when failing.

This genuine replacement door gasket creates an airtight seal around the refrigerator door to help maintain proper temperature and efficiency. It restores sealing performance to reduce frost buildup and stabilize internal cooling. What it does:

• Seals the refrigerator door edge to keep cold air in and warm air out
• Helps prevent frost and ice buildup in the freezer/refrigerator compartment
• Reduces compressor run time caused by a leaking door seal
• Improves temperature consistency for food preservation

• Disconnect power to the appliance before starting any work
• Clean and dry the door flange thoroughly before installing the new gasket
• Press the gasket into the channel evenly, working around the door to align the magnetic lip
• Inspect the seal after installation and allow normal operation to seat the gasket; check for gaps and re-seat if needed

The pads are an OEM component of Whirlpool refrigerators equipped with built-in ice and water dispensers. These paddles are responsible for dispensing ice on demand when the lever is engaged.

Symptoms of faulty dispenser paddles include:

• Difficulty dispensing ice or inability to dispense at all
• Ice getting jammed or stuck inside the dispenser chute  
• Grinding or clicking noises coming from the dispenser area

Causes can relate to wear from years of repeated use, or damage from blockages like crushed ice. Paddles may become bent or broken over time.

This OEM part fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brand models.

This compressor grommet is the rubber isolator that cushions the refrigerator's compressor at its mounting points. Replacing a worn grommet helps quiet vibration and rattling and reduces stress on refrigerant tubing for smoother, safer operation.

• Isolates the compressor from the base to damp vibration and humming
• Helps prevent metal-to-metal contact and rattling at the mounts
• Supports proper compressor alignment to reduce stress on tubing
• Helps with symptoms like loud buzzing/rattling or cracked/flattened rubber at the compressor feet

• Unplug the appliance and remove the rear access cover to reach the compressor area
• Support the compressor while removing hardware; replace the grommet in the same orientation
• Avoid kinking or stressing refrigerant lines; no sealed-system opening is required
• Tighten mount fasteners evenly and ensure the compressor sits level and isolated

Replacement drip tray that collects defrost and condensation water and channels it to the drain path, helping prevent leaks and water damage in the refrigerator cabinet. What it does

• Captures defrost and condensation water from the evaporator area and routes it to the drain pan.
• Prevents water pooling inside the cabinet or onto the floor when functioning properly.
• Common symptoms of a failing tray: visible water under the fridge, leaks from the base, or damp/musty odors.
• Designed for select Whirlpool refrigerators.

• Disconnect power before servicing to avoid electrical shock.
• Access and remove the old tray by removing the lower access panel or toe grille; replace with the new tray and secure panels.
• Ensure the tray and drain path are aligned and clear of debris so water can flow to the drain pan.