Wsm2780 Parts

Replacement rotary control knob for washer dryer combos. Restores manual control of temperature and function settings when original is cracked, worn, or missing.

Dryer won't advance through cycles or stops mid-cycle? This timer control board restores automatic cycle progression in your washer dryer combo unit.

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal

Door hinge for dryers. Attaches the door to the dryer cabinet frame, allowing it to open and close smoothly. Replace if cracked, broken, or worn.

Dryer won't heat or stops mid-cycle? This thermal limiter cuts power when temperatures exceed safe limits. Common DIY repair, takes 30-45 minutes.

Heat shield baffle that mounts to the back of the dryer drum. Replace if cracked, broken, or missing to protect drum components from direct heat exposure.

Replaces a cracked, broken, or missing dryer drum baffle that lifts and tumbles clothes during the drying cycle. Restores proper tumbling action.

Dryer not heating properly or overheating? This resistor regulates temperature control in your dryer. Common repair for inconsistent heat issues.

Short vertical spring for washer dryer combo tub suspension assembly. Replacement for broken, worn, or missing springs that affect drum alignment and stability.

This is a replacement pointer for control panels and timer knobs that restores a clear, visible indicator of the selected setting. It helps you quickly see and select the correct cycle or temperature. What it does:

• Replaces a cracked, broken, faded, or missing pointer so the control position is visible
• Aligns with the control knob to show the active setting or timer position
• Improves usability when the original pointer is worn or detached
• Matches the original white/dark gray color for a clean appearance

• Always disconnect power (unplug the appliance or shut off the breaker) before servicing
• Remove the control knob as needed, then press the pointer into the control shaft or bezel until it seats
• Do not force the part; stop and verify the part number and control style
• Refer to the appliance owner's manual or a repair guide for model-specific removal steps

Fix a washer dryer combo that won't start, stopped mid-cycle, or produced a burning smell. This capacitor restores power to the motor. DIY repair.

This ATC temperature control board regulates the refrigerator's temperature and ensures consistent cooling cycles by directing fans, compressors, and defrost operations. Replaces a failed control board to restore normal temperature control and cycle timing. What it does:

• Controls thermostat signals to the compressor and evaporator fan for stable internal temperatures
• Manages defrost cycles and related heater operation if applicable to the model
• Helps stop erratic cooling, excessive frost buildup, or continuous running when the board fails
• Works as the electronic decision hub when mechanical thermostats are replaced by board-driven control systems

• One ATC temperature control board (WH12X10386)

• Disconnect power and unplug the appliance before starting any repair
• Handle the board by its edges and avoid touching circuitry to prevent ESD damage
• Verify harness connector orientation and secure all plug connections; do not force connectors

Cushions and spaces the transmission-tub interface to reduce wear and maintain smooth spin. Replace if you notice abnormal noise or vibration. Confirm fit.

Stainless steel mounting screw for washers and washer dryer combos. Replaces damaged, stripped, or missing screws that secure components during operation.