Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
6-20 x 3/8 in. screw secures panels and brackets inside washers. Replaces missing, stripped, or damaged fasteners to restore proper fit and stability.
I had to remove the front panel of the washing machine and top of the washing machine. i started by removing all the top screws as shown in one of videos. disconnected all the electrical wires (i have a commercial washer) and lifted the front panel over the back of the machine. i was then able to remove the top of the washing machine to give me access to the tub straps and the corresponding screws. i removed the broken straps and then was able to remove the tub cover by pushing down it down... Read more
Replaces worn or damaged washer sound dampening isolator. Reduces vibration and noise during wash cycles. Essential when original is cracked or missing.
Replaces a short wireform hinge that secures your washer lid or access panel. Order a new hinge if yours is rusted, bent, cracked, or missing.
Removing and Replacing (R&R) the parts took about 15 minutes. Getting the correct parts took several weeks. It was a severe struggle. Many of you will experience problems trying to get the correct "Lid" for similar GE washing machine models. AppliancePartsPros.com was great: Right price, Arrived quickly in good condition. I got the wrong part. It was not the fault of AppliancePartsPros.com, though. To make a long story short, GE has disseminated incorrect data in parts lists and it... Read more
Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.
Size: 1/4 - 20 b.
OK kids, pay attention! This was my second attempt @ this repair. My first repair started leaking right away and had to be re-done about 6 months later. HERE IS THE PROBLEM!. In the video, you'll notice that (while putting it back together) when you put the square hole washer and split-ring over the shaft, they look to land atop the rubber seal, buy when you do this in real life, there is a gap between the seal and the washer. (This gap was close to a 1/4 inch). I THINK that the first time I... Read more
Size: 8-18 b.
Purchased new RPS Hall Effect sensor, pulled rotor and stator and installed new RPS module. Works fine after new sensor! Repair took about 30 minutes. Perfect! Read more
Grounding clip for top-load washers ensures proper electrical grounding. Replace if damaged, corroded, or missing to maintain safe operation. Verify fit with your washer model number before ordering.
Fix a washer that won't spin or agitates weakly with this motor and clutch kit. Solves pulsing motors and failed spin cycles. DIY repair takes 2-3 hours.
Handy Husband took off front of washing machine, unbolted motor then I held motor in place while he bolted on new one.He had to connect new wire harness.One wire was different color..orange instead of white with red stripe.He wrapped old hanging wires to steel bar supporting drum and new wire harness attached to inside where original used to be.He put on the new belt as well since old one was a bit old.He needed a phillips, metric tools..sockets, wrenches, wire cutters,a crimper, pliers and it... Read more
Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.
Ordered new hose from appliance parts pro. Part came in 2 days. Easy to replace. Read more
Usually ships within 4 - 14 days
Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.
Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.
5/16-18 tpt ihw s n
Replaced the Coupling Pulsator, and the Pulsator (short spindle in the center of the washer). The only problem that I encountered was how to remove the short spindle in the center of the washer...my fabric softer is in the center and you need to open that, grab the middle and loosen by turning left. Once that is out you will use a 7/16th socket and remove the entire agitator. Most of the videos show that you pull that straight up to remove - not the short one. There is still a screw to remove.... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.