Wt1510cw Parts

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

This multi wiring harness routes power and signals between components to restore reliable electrical connections in the appliance. It replaces damaged or worn wiring to help eliminate intermittent operation or loss of function. What it does:

• Connects multiple electrical components through a single harness to ensure coordinated operation
• Replaces frayed, burnt, or broken wires and corroded terminals that cause intermittent or no power
• Restores proper signal paths for sensors, switches, motors or valves served by the harness
• Helps eliminate shorts, arcing, or erratic component behavior caused by damaged wiring

• One multi wiring harness as shown

• Disconnect all power (unplug appliance or shut off breaker) before starting any work
• Document or photo-mark connector locations before removal to ensure correct reassembly
• Route the harness following original clips and fasteners; avoid contact with sharp edges or hot surfaces
• If terminals or connectors are damaged, replace the entire harness rather than splicing unless specifically approved by manufacturer

This is the main control board — the electronic PCB that manages a unit's user interface, cycles, and sensor signals so the appliance runs the correct programs. Replacing a faulty board restores control and communication functions. What it does:

• Receives input from buttons/knobs and runs the selected cycle logic
• Sends commands to motors, valves, heaters, and other components
• Monitors sensors and returns status to the display or error reporting
• Commonly replaced when the appliance won't start, shows no display, has unresponsive controls, or cycles incorrectly

• One main control board (PCB assembly) as pictured

• Disconnect power (unplug or switch off breaker) before starting any repair
• Handle the PCB by the edges and avoid static discharge; use an anti-static strap if available
• Verify connector positions and orientation before removing wires; label wires or take photos

This nozzle assembly directs and focuses spray for proper cleaning or dispensing, restoring correct fluid flow and spray pattern. It helps maintain performance and prevents uneven distribution during operation. What it does:

• Directs spray or fluid flow to the correct area for cleaning or dispensing
• Restores even spray pattern and coverage for improved cleaning performance
• Helps stop erratic or weak spray caused by a damaged or clogged nozzle
• Can reduce leaking or overspray from a broken or misaligned nozzle

• One nozzle assembly

• Disconnect power and shut off water supply before starting
• Access may require removing exterior panels or dispenser components; keep track of screws and fasteners
• Inspect mounting gasket or seals and replace if worn to prevent leaks

This lid assembly replaces a damaged or broken top lid on a top-load washer, restoring a secure cover that helps contain water and lets the machine close and latch properly. It fits the washer's lid opening and hinge location. What it does:

• Replaces a cracked, warped, or missing top lid so the washer can close and latch
• Helps prevent water and detergent from escaping during fill and agitation
• Restores the proper surface for the lid latch and hinge to engage
• Resolves symptoms like a lid that won't close, visible cracks, or a loose hinge area

• Disconnect power and water supply before starting any repair.
• Remove screws and retainers holding the existing lid; support the lid to prevent dropping.
• Align hinges and secure fasteners evenly; check that the lid opens, closes, and latches smoothly.

A standard replacement bolt used to secure appliance panels and internal assemblies. This OEM-style fastener restores proper fit and reduces movement that can cause noise or misalignment in appliance components. What it does:

• Fastens panels, brackets, and components to maintain structural integrity
• Keeps moving parts aligned to help prevent rattling or vibration
• Replaces missing, loose, or corroded bolts that compromise fit
• Suitable where a standard machine/sheet-metal bolt is required

• One bolt

• Disconnect power and water before servicing the appliance
• Use the correct driver/socket to avoid stripping the head or threads
• Tighten securely but avoid over-torquing; replace any damaged nuts or washers
• Inspect mating threads and clean or chase threads if corroded