Wt6001 Parts

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This detergent box is the molded dispenser drawer that holds and releases liquid or powdered detergent into the wash tub during cycles, helping ensure detergent is delivered where needed for cleaning. What it does:

• Holds liquid or powdered detergent and channels it into the washer during the fill and wash cycles
• Helps prevent detergent from spilling into the cabinet or away from the wash water
• Common symptom of failure: detergent leaks, fails to dispense, or sits in the drawer instead of flowing into the tub

• One detergent box (dispenser drawer) as shown

• Remove power and water connections before accessing the dispenser area
• Inspect surrounding seals and mounting tabs; replace if damaged to ensure a proper fit
• Clean the dispenser area and rinse with water before installing the new box to remove residue

This softener dispenser cap replaces the worn or cracked cap that covers the fabric softener chamber, restoring proper containment and controlled release of liquid softener during the wash cycle. A simple, low-cost part that prevents leaks and keeps the dispenser functioning. What it does

• Covers and seals the fabric softener compartment so liquid stays in the dispenser until the rinse cycle.
• Helps prevent softener from leaking into the washer drum between cycles.
• Restores a secure fit when the original cap is cracked, warped, or missing.
• Resolves issues with softener dispensing at the wrong time or pooling in the dispenser.

• One softener dispenser cap (1 piece)

• Disconnect power to the washer before accessing internal parts and follow all safety precautions.
• Typically accessed by removing the dispenser drawer or top panel—refer to your washer's service instructions.
• Inspect surrounding dispenser components for damage and replace any worn parts to ensure a proper seal.
• No electrical connections; basic hand tools may be required.

This bracket assembly secures internal components to the appliance frame, restoring stable support and alignment for panels or assemblies. Replacing a damaged bracket helps stop rattling and prevents misalignment that can affect operation. What it does:

• Provides a secure mounting point for panels, control boards, or internal assemblies
• Restores proper alignment to reduce vibration, noise, or rubbing parts
• Prevents loose components that can cause intermittent contact or wear
• Re-establishes structural support after impact, corrosion, or bracket failure

• One bracket assembly

• Verify power is disconnected before starting any repair
• Inspect mounting screws and adjacent parts; replace any damaged fasteners
• Tighten to manufacturer torque where specified and confirm proper alignment

This tapping screw fastens appliance panels and components for a secure, lasting hold. Replace stripped, rusted, or missing hardware to restore proper fit, reduce vibration and rattling, and keep brackets, covers, and trim tightly in place.

• Fastens metal or plastic panels, trim, or brackets to the appliance cabinet/frame
• Cuts its own threads in pre-drilled holes for a tight, reliable fit
• Helps maintain alignment and reduce movement that can cause noise
• Replace when the original screw is missing, stripped, corroded, or will not tighten

• Disconnect power and shut off water/gas before servicing
• Match the screw's position and length to the original hardware
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any washers or spacers from the original assembly if present

This bracket assembly secures and supports internal appliance components, restoring proper alignment and stability to parts that have shifted or come loose. It provides a direct replacement to maintain safe, reliable operation. What it does:

• Provides a sturdy mounting point to keep panels, modules, or assemblies properly positioned
• Helps eliminate rattling, misalignment, or loose component movement
• Restores intended structural support after impact or wear
• Works as a direct-fit replacement to return original fit and function

• One bracket assembly

• Disconnect power (and water, if applicable) before beginning any repair
• Use appropriate tools and keep fasteners for a secure fit; replace damaged screws as needed
• Inspect surrounding components and wiring for damage before reassembly

This damper controls airflow between compartments to help maintain consistent temperatures and efficient cooling. It replaces a worn or failed damper to restore proper air distribution and reduce temperature swings. What it does:

• Regulates airflow between freezer and fresh-food compartments for balanced temperatures
• Can cause uneven cooling or warm fresh-food compartment when faulty
• May click, stick, or fail to open/close if broken or obstructed
• Works with the refrigerator's control system to adjust airflow based on settings

• Disconnect power before beginning any service to avoid electric shock
• Handle the damper and housing carefully to avoid damage to plastic fins or linkage
• Note orientation and actuator connection before removal to ensure correct reassembly
• Test operation after reinstalling by restoring power and cycling temperature controls

This inner tub hub connects the washer's inner drum to the drive assembly, providing a secure rotational link so the drum can spin properly. Replacing a damaged hub restores drum stability and reduces noise or wobbling. What it does:

• Secures the inner tub to the drive shaft so the drum turns with the motor
• Prevents excessive movement, vibration, and scraping noises caused by a worn or broken hub
• Helps correct spin-related issues like uneven spinning or the drum not engaging
• Works with the tub assembly and other drive components to maintain proper drum alignment

• One inner tub hub

• Disconnect power and water supply, and fully drain the washer before starting
• Replacement generally requires removing the outer tub/inner tub assembly and transferring seals or gaskets as needed
• Use proper tools and follow OEM service instructions
• Inspect surrounding components (seals, bearings, suspension) and replace if worn to prevent repeat failure

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This detergent box assembly replaces the washer's front detergent/dispenser drawer so detergents and additives dispense cleanly during cycles. It restores proper product delivery and helps reduce residue build-up in the dispenser area. What it does:

• Houses and channels liquid and powdered detergents and additives into the wash at the correct time
• Prevents detergent from pooling or leaking into the washer cabinet when functioning correctly
• Reduces visible residue and clogging in the dispenser area that can affect dispensing
• Compatible with front-load washer detergent/dispenser systems that use a removable drawer

• One detergent box assembly

• Remove power and water supply before beginning service
• Typically installs by sliding into the dispenser housing and securing any retaining clips or screws
• Inspect surrounding seals and rails for damage and clean any residue before installing the new assembly

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and vibration for reliable operation. It's a simple replacement part that restores proper fit and stability. What it does:

• Secures and supports nearby components or assemblies to prevent shifting
• Reduces vibration and rattling that can cause noise or wear
• Helps maintain correct alignment for connected parts to operate smoothly
• Restores original component retention after damage or loss of the bracket

• Disconnect power to the appliance before beginning any repair
• Basic hand tools may be required; handle small parts carefully to avoid loss
• Inspect surrounding clips and fasteners; replace any that are damaged

This heater assembly replaces the dryer's heating element and housing to restore warm airflow for drying cycles. It's a direct-replacement assembly that re-establishes the appliance's heat source when the dryer won't heat properly. What it does:

• Houses the electric heating element that produces heat for drying cycles
• Replaces a burned-out element, open circuit, or damaged housing that can stop the dryer from heating
• Helps resolve symptoms such as no heat, only air tumbling, or weak/partial heating
• Works with the dryer's blower and thermostat to deliver consistent drying temperatures

• One heater assembly (heating element installed in housing)

• Disconnect power to the dryer (unplug or shut off breaker) before servicing
• Allow components to cool and wear gloves to protect hands from sharp edges
• Verify the part number matches the dryer's parts list before installation

This suspension assembly supports and stabilizes the washer tub to control movement and vibration during spin. Replacing a fatigued suspension restores smoother, quieter operation and helps prevent banging, walking, and out-of-balance errors.

• Supports and centers the tub within the cabinet
• Absorbs movement and vibration through wash and spin cycles
• Helps reduce noise and shaking during high-speed spin
• Addresses symptoms such as loud thumping/banging, washer "walking," excessive vibration, UE/uE out-of-balance errors, or a tub that leans/sags

• Disconnect power and water; close supply valves before servicing
• Wear gloves and support the tub when removing the old suspension to prevent a sudden drop
• Transfer any mounting hardware or brackets from the original part if required
• Level the washer and run a test cycle to ensure proper balance and operation

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings