Wtmc 632Sus Parts

This hose inlet is the water connection hose that routes incoming water to the appliance's inlet valve, restoring proper water feed for cycles. It's a direct-fit replacement designed to match the original part's fit and function. What it does:

• Connects the home water supply to the appliance's inlet valve so water can enter for wash/fill cycles
• Restores proper water flow when the original hose is cracked, split, or leaking
• Helps prevent leaks at the machine entry point when the hose and clamps are properly installed
• Works as the factory-style replacement to maintain correct routing and seal

• One hose inlet

• Turn off power and shut off the water supply before attempting replacement
• Drain residual water from the supply line and appliance to minimize spills
• Inspect and replace any worn clamps or seals; hand-tighten then secure clamps per manufacturer guidance

This sealing strip replaces a worn or damaged door edge seal to help maintain a tight closure and reduce leaks, drafts, and odors. It restores proper sealing where the door meets the cabinet or frame. What it does:

• Provides a consistent seal along the door edge to help prevent water or air leaks
• Helps limit odors and moisture transfer from the appliance compartment
• Reduces rattling or wind noise caused by a compromised door seal
• Restores smooth door closure and alignment where the strip seats

• Disconnect power and water supply before starting work
• Remove the old strip carefully to avoid damaging the door or frame
• Align the new strip with the door edge and press into the channel or mounting surface per OEM guidance
• Trim excess only if specified by the manufacturer; check for a secure, continuous seal after installation

This genuine refrigerator door seal replaces a worn or damaged gasket to help restore proper door sealing and keep cold air inside. It reduces cycling and helps maintain consistent temperatures for stored food. What it does:

• Creates a tight seal around the refrigerator door to prevent air leaks
• Helps stop frost buildup and reduces overworking of the compressor
• Commonly replaces seals that are torn, flattened, or no longer sealing
• Fits specific Bosch refrigerator doors — improves cooling performance when seal is compromised

• Disconnect power to the appliance before starting any repair
• Remove food, shelves, and door liners as needed for access
• Warm the gasket slightly (room temperature or warm water) to ease installation; avoid open flames or excessive heat
• Inspect door frame for damage and ensure the seal is seated evenly to allow full door closure

This flat washer secures fasteners and helps distribute clamping force to protect parts from pull-through and wear. It's a small but critical hardware piece that helps maintain proper alignment and reduce vibration in the appliance. What it does:

• Sits under a nut or bolt to evenly spread load and prevent surface damage
• Helps keep fasteners tightened and reduces loosening from vibration
• Protects mating surfaces from wear and deformation
• Can reduce rattling or vibration-related noise when used as intended

• Disconnect power and water before accessing internal components
• Replace like-for-like; do not force or modify the washer to fit
• If other hardware is corroded or damaged, replace affected fasteners as a set

This Cap is a small protective closure used to cover and protect exposed openings or fittings on compatible Bosch appliances, helping keep dirt and moisture out for reliable operation. What it does:

• Covers exposed openings, ports, or fasteners to prevent debris and moisture intrusion
• Helps maintain proper alignment and protection of small components
• Stops small leaks or drips when used as a sealing closure in low-pressure areas
• Useful when the original cap is cracked, missing, or worn

• One replacement cap

• Install by snapping or pressing into place; no special tools typically required
• If the cap is near electrical components, disconnect power before replacing
• Replace if cracked or deformed to restore proper protection

This replacement access cover protects internal components and restores a finished appearance to the appliance. It helps keep wiring and small parts shielded from moisture, dirt, and accidental contact. What it does

• Shields internal components and wiring from debris and accidental contact
• Restores the appliance's finished appearance where the original cover was cracked or missing
• Helps reduce rattling caused by a loose or damaged cover
• Can prevent moisture and small-parts ingress that may lead to further damage

• One cover

• Disconnect power and water supply before beginning any repair
• Remove any surrounding panels or fasteners to access the damaged cover; keep track of screws and clips
• Align tabs or screw holes and reinstall with the original hardware; do not force or bend the part