Wtmc5330us16809644 Parts

The Door Hinge is an OEM part for Bosch dryers. This hinge is designed to securely attach the dryer door to the frame, allowing it to open and close smoothly while maintaining a proper seal during operation.

Causes of a bad door hinge can include regular wear and tear, damage from excessive force when opening or closing the door, or corrosion from exposure to moisture and heat.  

Symptoms of a bad door hinge include:

• The dryer door not closing properly or staying open
• Difficulty opening or closing the dryer door
• A misaligned dryer door
• Unusual noises or resistance when moving the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Thermister

Dryer not heating or shutting off mid-cycle? A faulty temperature limiter is often the cause. Simple 15-minute fix—just remove back panel and replace.

Supports smooth drum rotation in your dryer. Replace if you hear squeaking, whistling, or rumbling during cycles. Verify fit with your model number.

Captures lint and debris during drying to prevent buildup and maintain airflow. Replace when clogged, torn, or causing sensor errors. Confirm fit with your model.

Dryer door won't stay closed or won't start? A broken door latch is often the cause. This replacement latch is a straightforward 5-10 minute fix.

Drum support roller wheel for Bosch dryers. Mounts on axle shafts to stabilize and support the rotating drum. Replace when cracked, worn, or squeaking.

Dryer stops after a few seconds with lint light on? A faulty moisture sensor may be the cause. Mineral buildup distorts humidity readings in the drum.

Replacement screw secures appliance panels, brackets, and internal components. Install when original is stripped, missing, or corroded for proper alignment.

Dryer overheating or won't start? A faulty relay prevents proper heater control. This electromechanical switch restores on/off control. Easy DIY fix.

Replace your worn dryer door sealing strip to restore a tight closure and prevent air leaks, drafts, and odors. Verify fit with your model number.

The Screw is an OEM part for Bosch gas cooktops and ranges. It anchors the surface burner head assembly onto the cooktop surface.

Causes can be stripped threads or overall wear from repeated heating/cooling cycles. Exposure to cooking spills or impacts may also deteriorate the screw head over time.

Symptoms of a bad burner head screw include:

• A burner detaching from the cooktop surface entirely
• Excess movement or instability of burner heads when in use
• Gas leaks reported around the burner head connection points

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This fan wheel circulates air through the appliance to support drying and cooling cycles, restoring proper airflow and temperature regulation. Replaces a worn or damaged blower impeller to improve performance and reduce overheating risk. What it does:

• Spins to draw and push air through the appliance's vent and heating chamber.
• Restores airflow when a cracked or warped wheel causes weak drying or poor ventilation.
• Can reduce unusual rattling or grinding noises caused by broken blades or imbalanced rotation.
• Helps prevent overheating by maintaining designed air movement.

• One fan wheel

• Disconnect power (and gas supply, if applicable) before beginning service.
• Access the blower housing; confirm orientation and fit before final assembly.
• Inspect surrounding seals and fasteners; replace any damaged clips or screws to ensure secure mounting.
• If you hear continued noise or airflow problems after install, re-check wheel clearance and shaft/bearing condition.

Fix washer not filling or slow water flow with a new inlet hose. Replaces cracked or leaking hoses that prevent proper water delivery to your machine.

Small mounting clip that secures dryer exterior panels and trim in place. Replace if clip is broken, cracked, or missing to restore snug panel fit.

This factory fastener secures appliance components and panels so they stay aligned and quiet. Replacing a missing, stripped, or corroded screw restores a tight fit and helps prevent vibration, rattling, and premature wear.

• Secures brackets, covers, panels, or internal parts per your model's design
• Helps maintain alignment and reduce vibration/noise during operation
• Replaces lost, stripped, rusted, or damaged hardware
• Common signs include loose or shifting panels, rattling sounds, or a missing screw found during service

• Disconnect power before servicing; shut off water or gas if applicable to your appliance
• Match the screw to the original location/length; replace one at a time to avoid mix-ups
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Use the correct driver for the head type on your model to avoid stripping