Wtw1500 Parts

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

This electronic control board replaces the appliance's main console controller to restore reliable touchpad/display operation and cycle control. It resolves electronic control failures that prevent normal operation and user interface function. What it does:

• Manages user inputs, display messages and cycle selection
• Controls timing and power to motors, valves and heaters per program
• Can stop operation or show errors when the board fails
• Common symptom: no display, unresponsive controls or erratic cycles

• Disconnect power before removing or installing the board to avoid shock
• Handle the board by edges; avoid touching contacts or components
• Verify model and part number match your appliance before ordering

This electronic control board is the appliance's primary control module that manages cycle settings and electronic functions, restoring responsive controls and proper cycle operation when the original board fails. What it does:

• Controls user inputs, timing, and electronic signals for cycles and options
• Regulates start/stop and cycle sequencing for consistent operation
• Can correct symptoms such as unresponsive controls, error codes related to the control, or intermittent cycle problems
• Works with associated harnesses and components to relay commands to motors, valves, and heating elements

• Disconnect power before service to avoid shock; verify power is off at the breaker
• Access may require removing a back or console panel; keep fasteners organized
• Handle the board by edges and avoid static discharge; use anti-static precautions if available

This idler pulley keeps the dryer drive belt tensioned so the drum turns smoothly, restoring normal drum rotation and reducing noise. It's a direct-fit replacement when the pulley is worn or seized. What it does:

• Maintains correct tension on the dryer drive belt so the drum spins without slipping
• Helps eliminate squealing, grinding, or rumbling noises from the dryer
• Prevents belt wear and premature belt failure due to misalignment
• Keeps the drum rotating smoothly for even drying and proper cycling

• One idler pulley

• Unplug the appliance and move it to a safe, well-lit area before beginning
• High-level steps: access the dryer cabinet, release belt tension, remove old pulley, install new pulley and re-tension the belt
• Use hand tools and follow OEM torque/placement; avoid forcing parts to prevent damage

This upper wiring harness connects the washer's control panel and sensors to the main electronics, restoring reliable communication and power to the control area. It's used when controls, display, or related functions lose power or responsiveness. What it does:

• Routes and secures electrical connections between the control board, display, and user interface components
• Restores power and signal paths so buttons, touchpads, and indicators function correctly
• Common symptom: control panel is unresponsive or display shows errors/no power
• Common symptom: intermittent operation or machine won't start due to faulty panel wiring

• Disconnect power to the appliance before starting any repair
• Handle connectors carefully; match connector shapes and latch positions during installation
• Route harness along original clips and ties to avoid pinching or heat exposure

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This absorber is the factory-design replacement part that restores the appliance's intended absorption function, helping maintain normal operation and reduce related performance issues. What it does:

• Absorbs and manages moisture/condensate or trapped vapors in the appliance's system to support normal function.
• Helps prevent symptoms commonly linked to a failed absorber, such as excess moisture, unusual odors, or intermittent system cycling.
• Restores the original fit and function when the installed absorber is cracked, broken, or heavily degraded.
• Matches OEM shape and connection points for a direct replacement.

• One absorber replacement as shown

• High-level replacement: access the absorber location; no specialized calibration typically required.
• Disconnect power (and water supply if applicable) before removing panels or replacing parts.
• Handle carefully to avoid damage to surrounding components and wiring; use manufacturer-recommended fasteners.

This electronic control board replaces the appliance's main control assembly to restore normal operation and control of cycles. It accepts signals from the user interface and manages timed functions, heating, and motors for reliable performance. What it does:

• Processes user inputs and runs the appliance's programmed cycles
• Controls timing, relays, and power to components like elements, fans, and motors
• Can resolve issues such as unresponsive controls, erratic cycles, or failure to start
• Works as the central logic module coordinating sensors and outputs

• Disconnect power before servicing to avoid shock; verify power is off at the breaker
• Handle the board by its edges and avoid contact with circuitry or components
• Ensure connectors are fully seated and any mounting hardware is secured

This electronic control board is the main control module that manages cycle functions and timing for the appliance, restoring responsive controls and correct cycle operation when the original board fails. What it does:

• Receives user inputs and runs the appliance's selected cycles and options
• Controls timing, relays, and signals to motors, valves, and heating elements
• Resolves symptoms such as unresponsive controls, erratic or stuck cycles, or failure to start
• Replaces a failed or damaged control board to restore normal electronic operation

• One electronic control board

• Disconnect power before servicing to avoid shock—this is an electrical component
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Verify connectors and wire harness locations match before powering the appliance

This replacement water inlet hose connects the household water supply to the appliance's water system, restoring reliable water flow for ice makers and dispensers. Durable construction helps prevent leaks and ensure steady operation. What it does:

• Carries water from the household supply to the appliance's water system
• Restores water delivery to the ice maker and dispenser when a hose is damaged or leaking
• Helps prevent leaks when flexed or routed correctly
• Compatible with the factory fittings and routing used on the original assembly

• Disconnect power and shut off the water supply before servicing
• Inspect fittings and seals; replace damaged clamps or gaskets as needed
• Tighten connections to manufacturer torque recommendations to avoid leaks

The Drive Motor is an OEM part for Whirlpool washers. It is responsible for powering the drum's rotation during wash and spin cycles. 

A bad drive motor can occur due to electrical issues, mechanical failures, or excessive wear and tear. If you notice symptoms such as the drum not spinning, unusual noises during operation, or error codes appearing on the control panel, it may be time to replace the drive motor.

Symptoms of a bad drive motor include:

• Drum not spinning or rotating
• Unusual noises during operation
• Error codes displayed on the control panel

Restore your washer by replacing the faulty or damaged drive motor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This control console houses the appliance's user controls and display so you can operate cycles and settings reliably. It restores a damaged or nonfunctional front control area for safer, more accurate use. What it does

• Provides the mounting and interface for buttons, knobs, and display so selections register correctly
• Replaces cracked, melted, or cosmetically damaged front-control surfaces
• Can resolve unresponsive or intermittent button/selector behavior when caused by a damaged console
• Restores proper alignment and protection for internal control components

• One console (control panel assembly) as shown

• Disconnect power (and gas supply for gas appliances) before starting work
• Handle the display and button areas carefully to avoid damage to delicate switch and ribbon connections
• Retain mounting screws and trim; some panels use clips that must be flexed for removal/installation

This Motor-Drive assembly powers the washer's drive system so the tub can agitate and spin properly. Replacing a worn or failed drive motor restores normal drum rotation and helps reduce noise from a failing motor. What it does

• Provides rotational force to the washer drive system so the tub can agitate and spin.
• Restores normal wash and spin cycles when a motor has failed or seized.
• Resolves symptoms like no agitation, no spinning, loud humming or grinding from the washer during operation.
• Works as the mechanical drive source; electrical diagnosis may be required if symptoms persist.

• Disconnect power before beginning any repair. Verify the appliance is unplugged.
• Basic mechanical skill and common tools are required; keep parts and fasteners organized during disassembly.
• Inspect wiring and connectors for damage before installing the new motor; replace any damaged harnesses or connectors.