Wtw1500 Parts

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This rubber pad cushions and protects appliance components from vibration and abrasion, reducing noise and wear. It's a small replacement part that restores proper contact and dampening where original pads have worn or fallen off. What it does

• Cushions panels or components to reduce vibration and rattling
• Prevents direct metal-to-metal contact that can cause scratching or wear
• Helps stabilize parts that have shifted due to a missing or damaged pad
• Commonly replaced when noisy operation or visible pad deterioration occurs

• One replacement pad

• Disconnect power before accessing interior panels or components
• Remove any retaining clips or panels that block the pad's location; pad typically presses into place
• Verify orientation and seating against the mating surface; replace any worn fasteners or retainers
• If adhesive was used on the original, use an OEM-recommended adhesive only.

This lid is the washer's top cover that protects internal components and provides a secure closure for normal operation. It restores a solid, intact top surface so the washer can close and latch properly. What it does:

• Covers and protects the washer's inner tub and control area from debris and moisture
• Provides the surface that the lid latch engages so the washer can start and run
• Prevents access to moving parts for user safety
• Fits where a cracked, warped, or broken top surface causes improper closing or visible damage

• Disconnect power to the washer before starting any repair
• Handle carefully to avoid sharp edges or dropping; use a second person if needed
• Remove mounting screws or hinges to lift off the old lid and align the replacement so the latch and hinges engage
• Verify lid closes and the latch engages before returning the washer to service

The Wire Harness is an OEM part for Whirlpool washers. It is responsible for connecting various electrical components within the washer, such as the control board, motor, and sensors, allowing them to communicate and function properly.

A bad wire harness can be caused by several factors, including wear and tear, electrical faults, or physical damage. If you notice issues such as erratic behavior of the washer, error codes appearing on the control panel, or complete failure of certain functions, it may indicate a problem with the wire harness.

Symptoms of a bad wire harness include:

• Intermittent or erratic operation  
• Error codes on the control panel
• Certain functions or cycles not working 

Replace your faulty wire harness with this genuine OEM part to restore your washer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Note: Bearings are only available with the gearcase assembly.

This rear panel replaces the backguard that covers the appliance's rear housing, protecting internal components and wiring while giving the unit a finished appearance. It restores a safe, enclosed back area and helps prevent debris entry. What it does:

• Covers and protects control wiring, terminals, and components at the appliance rear
• Prevents accidental contact with electrical parts and reduces debris or grease buildup
• Restores a finished exterior back surface for safety and appearance
• Helps maintain proper airflow routing behind the appliance

• Disconnect power (unplug or shut off circuit breaker) before starting work.
• Handle edges carefully—metal panels may be sharp; wear gloves.
• Typical installation requires removing a few screws and aligning tabs; keep original fasteners if present.
• If clips, insulation, or mounting hardware are missing or damaged, replace with OEM-specified hardware for proper fit.

This replacement silverware/cutlery basket holds forks, knives and spoons so small items stay organized during dishwashing and drain properly. It restores a dedicated space for utensils and helps keep the rack tidy. What it does:

• Provides a secure compartment for silverware and small kitchen tools during wash cycles
• Keeps utensils separated to improve cleaning and prevent nesting
• Allows water to drain through while holding items in place
• Replaces a broken, cracked or missing utensil basket to restore functionality

• One replacement silverware/cutlery basket

• No special tools required; typically lifts in and out of the rack—align and set into place
• Inspect for broken tabs or clips on the rack that could prevent proper seating
• Disconnect power to the appliance before performing any repairs or heavy manipulation of racks
• If rack mounting hardware is damaged, replace hardware to ensure the basket sits securely