Wtw5015lw Parts

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The washer pulley Cover is an OEM replacement part for Whirlpool washing machines. It is a removable plastic shroud that houses the drive pulley and belt mechanism.

Causes of a bad pulley cover can include cracks or breaks from repeated opening and closing over time. Chemical or moisture exposure can also damage plastic through standard usage cycles. 

Symptoms of a failing pulley cover include:

• Inability to properly close or latch the cover  
• Leaks or debris entering the pulley compartment
• Interference with belt or pulley movement
• Loose fasteners or mounting points that cause misalignment

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore models.

The Washer Encoder Control Board is an OEM part for Whirlpool washing machines. As the central processing component, it regulates all cycle phases including wash, rinse, and spin speeds through electronic encoding commands. 

Symptoms of a bad encoder control board include:

• Inability to start or progress through cycle phases
• Failure to produce programmed wash motions  
• Not reaching intended rinse or spin speeds
• Unexpected behaviors like fast-forwarding

Causes can involve damage from water exposure over many years, power surges interfering with circuitry, or failures of electronic chips and sensors.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Amana, and some Kenmore washers.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes connector and both clamps.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

Replacement bearing that supports the dryer drum shaft and helps the drum rotate smoothly, reducing noise and preventing excessive wear. Use when you hear grinding, squealing, or notice drum wobble. What it does:

• Supports the drum shaft so the drum spins freely and stays aligned.
• Reduces grinding, squealing, or scraping noises caused by worn bearings.
• Helps prevent drum wobble and uneven wear on the drum and seals.
• Restores smoother operation and can extend life of adjacent parts when replaced promptly.

• Disconnect power before servicing; for gas dryers also shut off the gas supply.
• Access usually requires removing the dryer cabinet or drum — follow your model's service manual.
• Inspect adjacent rollers, seals and the drum shaft for wear and replace if damaged.

This ice dispenser drive motor powers the auger inside the ice bin, moving ice through the chute when you press the paddle. Replacing a weak or failed motor restores dependable dispensing of cubed or crushed ice. What it does:

• Rotates the auger to push ice from the bin to the dispenser chute
• Delivers the designed torque and speed for consistent dispensing
• Helps resolve ice not dispensing, auger not turning, humming/clicking from the door, or intermittent/slow dispensing
• Replaces a motor that is seized, noisy, or does not start

• 1 drive motor

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the motor per your model's service/owner documentation
• Note wire orientation; transfer the coupler, bracket, and screws from the original motor if required
• After installation, verify the auger turns freely by hand and test dispense before reassembly

Used from harness to top.

This replacement filter captures airborne grease and cooking particles from the vent system. It helps protect the blower and ducting and keeps airflow efficient so your hood or microwave-hood can clear smoke and odors more effectively. What it does:

• Traps grease and food particles to reduce buildup inside the vent path
• Helps maintain proper airflow and ventilation performance
• Replace when torn, warped, heavily saturated, or won't stay seated
• Common symptoms: lingering odors or smoke, greasy residue near the cooktop, visible damage to the filter

• 1 filter

• Disconnect power and allow the appliance and filters to cool before servicing
• Release the retaining tabs or latch and remove the old filter
• Seat the new filter fully and secure per your user guide
• Do not operate the appliance without all required filters installed

Right hand side. For screws use WPW10119828.

The Knob is an OEM component for Whirlpool dryers. As the user interface, it allows selections of temperature, settings, and time options with the twist of a finger.

Designed for comfort during extended cycles, the durable knob utilizes non-slip textured surfaces around robust internal gears. Integrated fasteners mount securely to shafts coupling knobs to their respective switches. 

Causes of faulty knobs can include stripped internal teeth from mineral deposits binding moving parts or broken mounting tabs weakened through normal wear over many years.

Symptoms of a damaged knob include:

• Failure to engage settings or spin freely  
• Dials loose on shaft allowing accidental shifts   
• Missing labels from normal cleaning/wear reducing visibility
• Cracks or breaks compromising seal against moisture

Replace yours today with this genuine Whirlpool knob to restore easy navigation of cycles. Compatible with Kenmore and some Maytag dryers.

This is the replacement top lid for a top-load washing machine. It restores the washer's ability to close securely and helps keep laundry contained during the wash cycle. What it does:

• Replaces a cracked, dented or warped lid that won't close properly
• Restores a proper seal to keep water, suds, and clothing inside the tub
• Helps the lid latch and safety switch engage so the washer can run
• Improves appearance by replacing a scratched or cosmetically damaged lid

• One replacement lid

• Disconnect power to the washer before attempting any repair
• Lids can be heavy or awkward—have a second person assist for safe handling
• Use manufacturer screws if provided
• If the lid attaches to a hinge or glass assembly, inspect related fasteners and switches for wear