Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is a plastic selector knob that comes with a retaining clip, used on the washer's control panel to select cycle settings. It attaches to the control shaft and allows you to choose wash cycles and options. Replace this knob if it is cracked, broken, or if the clip has snapped, causing the knob to spin freely or fall off the shaft.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.
Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more
Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
Replacement timer knob assembly for washers. Installs on the control panel timer shaft. Needed when original knob is cracked, broken, or missing.
Easily replaced the knobs Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Black. 8-18 AB HXW 3/8
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
These mounting screws secure various internal components within your washing machine. They hold parts like panels, brackets, and mechanisms in their proper positions during wash cycles. Replace if screws are missing, stripped, or causing rattling noises during operation.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.
Outer basket had a lot of rust on the lip at the top of the basket, I ordered tub gasket, but when I removed the old gasket, some of the lip broke off, leaving gaps at the top, went to the hardware store, and purchased thin sheet of 8x10" aluminum, cut and shaped pieces from this sheet, to fit under the damaged lip, to bridge the gaps, rounded edges to fit against the rounded part of the outer tub, under the lip, once shaped, I glued them in place with emblem adhesive, did this all the way... Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
This is an electrical relay used in the washer's motor or control circuit to switch power to specific components during operation. It helps regulate the timing and function of the wash and spin cycles. Replace this relay if the washer motor won't start, the machine hums but doesn't agitate or spin, or if cycles fail to advance properly.
Cushions and supports the washer leg to reduce vibration and protect flooring. Replace if cracked, worn, or missing to stabilize and level your unit.
I ordered new foot pads and replaced the old ones. Now the washer runs better that it did when it was brand new. Read more
Supports washer drum for smooth, quiet rotation during spin cycles. Replace if you hear grinding noise or excessive vibration. Verify fit with your model.
This is a rubber shaft seal that fits around the transmission or gear case shaft in the washer. It prevents water and detergent from leaking into the gear case and damaging internal components. Replace this seal if you notice oil leaking from the bottom of the washer or if water is dripping from the transmission area during the wash or spin cycle.
It is an old washing machine that is leaking oil from the transmission, and taking advantage of the disarmament want to change those parts that are damaged.the will rebuild replacing those parts and then paint it. Read more
To use with BOOT #wh8x246
This small replacement lid bumper cushions and supports the appliance lid, helping it close softly and stay aligned. It restores smooth, quiet operation where worn or missing bumpers cause rattling or uneven closing. What it does
It took only 5 minutes to remove the broken pieces and replace the new ones. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.