Zic360n Parts

This foam-filled freezer door panel provides the insulated inner surface that helps maintain cold temperatures and supports interior components. It replaces a damaged or worn inner door to help reduce frost buildup and improve cooling efficiency. What it does:

• Replaces the freezer's insulated inner door panel to restore proper insulation and structural support.
• Helps reduce temperature loss and potential frost accumulation when the outer door closes correctly.
• Supports door-mounted bins and shelves that attach to the inner panel.
• Common symptoms addressed: visible damage to the inner panel, soft or deformed door surface, or increased frost inside the freezer compartment.

• Disconnect power to the appliance before beginning any repair to avoid electrical shock.
• Installation typically requires removing the outer door trim and fastening hardware; handle the panel carefully to avoid damaging the foam core or mounting tabs.
• Inspect door gaskets and mounting hardware during replacement; replace any damaged components to ensure a proper seal.

This evaporator assembly circulates refrigerant and helps remove heat and humidity from the freezer compartment, restoring proper cold and frost control. Replaces the internal evaporator box to improve cooling performance and defrost function. What it does:

• Houses the evaporator coil to allow refrigerant evaporation and heat exchange
• Enables proper cold airflow and consistent freezer temperatures
• Supports the defrost cycle by routing meltwater to the drain system
• Commonly replaced for frost buildup, weak cooling, or abnormal freezer temperatures

• One evaporator assembly (evaporator box) as shown

• Requires access to the freezer interior; disconnect power before starting
• May require removal of shelving, panels, and the evaporator cover for access
• Follow OEM instructions for proper refrigerant and wiring handling; replace any damaged gaskets or seals

This 8-32 x 5/8" Phillips screw is a stainless steel fastener used to secure panels and components in appliances. It resists corrosion and provides a reliable, low-profile Phillips head fastening solution. What it does:

• Fastens panels, brackets and trim where an 8-32 x 5/8" screw is specified
• Stainless steel construction helps resist rust in humid or food-prep environments
• Phillips head accepts standard drivers for quick, positive installation
• Replaces worn or stripped fasteners that cause loose or rattling parts

• One 8-32 x 5/8" Phillips stainless steel screw

• Unplug the appliance or disconnect power before beginning work
• Use a properly sized Phillips screwdriver to avoid cam-out or stripping
• Tighten until snug; avoid over-tightening which can strip threads or crack plastics

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

This replacement key pivot is the small pivoting pin that supports the refrigerator/freezer door key or latch mechanism, restoring secure pivoting and smooth operation at the key location. A direct-fit OE-design replacement. What it does

• Provides the pivot point for the door/key mechanism so the key or latch rotates smoothly
• Restores proper alignment when the original pivot is worn, bent, or broken
• Helps prevent a loose or wobbly key or a latch that fails to engage
• Works as a simple, serviceable part of the door/lock assembly

• One key pivot

• Disconnect power to the appliance before beginning any repair
• Remove door trim or access panel as needed; keep small parts organized
• Replace the pivot and check movement; avoid forcing parts that do not align

This 10-24 x 1/2 screw is a direct-fit fastener used to secure appliance panels and components. It restores proper fit and prevents loose or rattling parts for safer, quieter operation. What it does:

• Fastens appliance panels, trim, brackets, or components where a 10-24 x 1/2 screw is required
• Replaces missing or stripped screws that cause loose panels, vibration, or misalignment
• Helps maintain electrical and mechanical connections by keeping parts securely mounted
• Suitable for interior and exterior appliance body attachment points using standard 10-24 threads

• Use the matching screwdriver or nut driver; avoid over-tightening to prevent stripping or cracking parts
• Disconnect power to the appliance before accessing internal panels or components
• Wear basic PPE (gloves/eye protection) when working on appliances