Ziss420dxss Parts

The Drain Pan and Heater Assembly is an OEM part for GE refrigerators. Located beneath the fridge’s evaporator coil, this pan collects condensed moisture that forms during normal operation. An integrated electric heating element prevents drain line freezing in cold environments.

Causes of a bad drain pan can include mineral buildup clogging drain hole fittings or cracks developing from constant temperature cycling. The heater coil may fail after years of heating moisture evaporation.

Symptoms include:

• Puddles of water under the fridge 
• Ice accumulation inside the pan hindering evaporation
• Non-functioning heater results in frozen or blocked drain line

This GE OEM replacement restores reliable moisture drainage with corrosion-resistant materials. The integrated automatic heater defrosts lines as needed to avoid backups or leaks from frozen condensate. Counts as an upgrade for GE and select Hotpoint or RCA side-by-side refrigeration models.

This inner drawer slide guides and supports a refrigerator drawer/bin so it opens and closes smoothly. Replacing a worn or cracked slide restores proper alignment and easy, consistent movement of the drawer.

• Provides guided travel for the drawer along the cabinet rails
• Helps keep the drawer level and properly aligned to prevent binding
• Replace if the drawer sticks, grinds, jumps track, or won't close fully
• Visible cracks, broken tabs, or excessive wobble indicate a failed slide

• Unplug the refrigerator before servicing; remove the drawer and its contents
• Note the orientation of the old slide and reuse the existing mounting hardware
• Install the new slide in the same position; tighten screws evenly without overtightening
• Test drawer movement and ensure it seats flush and glides smoothly end to end

The Collar Kit is an OEM component for GE side-by-side refrigerators with an external ice dispenser. It surrounds the door dispensing area and creates a seamless aesthetic transition point. Effective dispensing relies on this collar kit.

Causes of failure can involve cracked or weakened mounting clips that no longer hold the collar securely, dried-out sealing materials failing to block air/temperature loss, or broken plastic pieces altering proper alignment.   

Symptoms of a bad collar kit include:

- Dispensed ice having melted or softened exterior surfaces  
- Excessive warm air leakage noticeable near the dispensing area doorway
- Potential for liquid spills due to improper sealing

Note: Color Black

Replacing with this genuine GE collar kit ensures optimized sealing around the ice dispensing portal for dependable storage. Compatible replacements include Hotpoint, RCA, and Kenmore branded dispenser fridge models seeking to restore integrity and functionality.
 

A 6 x 1/2 inch pan-head Phillips screw used to fasten panels, trim, brackets and small assemblies on appliances. Replacing worn or missing screws restores secure mounting and reduces vibration or rattling. What it does:

• Fastens panels, brackets and trim where a 6 x 1/2 in. pan-head Phillips screw is required.
• Stops loose or rattling parts caused by missing, stripped or corroded screws.
• Provides the correct head profile for a Phillips driver to allow proper torque and seating.
• Used in non-structural fastening points on appliances.

• Always disconnect power and unplug the appliance before beginning repairs.
• Use the correct-size Phillips screwdriver to avoid cam-out and head damage.
• Do not over-tighten; over-torquing can strip threads or deform mating parts.
• Inspect mating threads and replace damaged components before installation.

A replacement auger motor assembly that powers the ice-dispensing auger so you can reliably move ice from the bin to the dispenser. Fits 36" and 42" dispenser configurations. What it does

• Turns the auger to feed ice through the dispenser chute
• Restores ice dispensing when the auger fails to rotate
• Stops unwanted motor noise or humming when the motor is the fault
• Works with the dispenser drive components to maintain consistent ice flow

• One auger motor assembly

• Disconnect power to the appliance before starting any repair
• Remove dispenser/ice-bin components and trim panels to access the motor per model instructions
• Handle electrical connectors and wiring gently; ensure secure connections before testing
• If water is present near the motor area, dry thoroughly and verify seals to prevent electrical shorts

This replacement vegetable pan assembly restores a sealed storage area in the refrigerator drawer to help keep produce organized and contained. Fits the drawer cavity to provide a moisture-controlled surface for fruits and vegetables. What it does:

• Replaces a cracked, warped or missing vegetable/produce pan so items sit securely in the drawer
• Helps contain spills and keeps small items from sliding under shelves
• Restores proper drawer fit and alignment for smooth opening and closing
• Reduces direct contact between produce and the refrigerator floor, aiding cleanup

• Disconnect power to the appliance before servicing to reduce risk of shock
• Remove drawer and any shelves or supports that obstruct access; handle parts carefully to avoid damage
• Slide the replacement pan into the drawer cavity until it seats evenly; no special tools typically required

This shear pin secures the washer agitator to the drive shaft and protects the transmission by designed failure when the agitator binds. It's a small, low-cost part that prevents costly gear or motor damage. What it does:

• Locks the agitator to the drive shaft so the washer can agitate and spin
• Designed to break (shear) if the agitator is jammed, preventing transmission or motor damage
• Commonly replaced when the agitator spins freely or the washer won't agitate
• Small part that restores proper mechanical coupling between agitator and drive

• One shear pin

• Disconnect power and water before starting any repair
• Access usually requires removing the agitator; follow your model's service instructions
• Verify shaft and agitator mating surfaces for wear or damage and replace if needed

This front dispenser plate replaces the exterior trim that surrounds the refrigerator dispenser opening, restoring a clean look and proper alignment for the ice and water dispenser area. It helps seal and protect internal dispenser components from dirt and damage. What it does:

• Covers the dispenser opening and provides a finished surface for the ice/water delivery area
• Helps guide ice and water into the drip tray and prevents interference with dispensing
• Protects internal dispenser switches and mechanisms from spills and debris
• Common signs you need this part: cracked, broken, warped or missing trim; loose or misaligned dispenser face

• Disconnect power to the appliance before beginning any work
• Removal typically requires releasing trim clips or removing a few screws; keep hardware for reassembly
• Handle carefully to avoid scratching the finish; align clips/screw holes before securing

This freezer basket assembly provides a durable, removable storage basket for organizing frozen foods and keeping items accessible in the freezer compartment. Replaces a damaged or missing freezer basket to restore storage function. What it does:

• Holds and organizes frozen food items for easy access and visibility
• Slides or nests securely in the freezer compartment to prevent tipping
• Restores lost storage capacity when an original basket is cracked or broken
• Helps keep items elevated for proper airflow around stored food

• Designed for drop-in or slide-in placement; no special tools typically required
• Remove food and unplug or power off appliance before servicing for safety
• Handle with care to avoid bending or damaging mounting points

This fill tube kit includes the water inlet tube used to route water to the dispenser/ice system, restoring proper fill delivery and helping prevent leaks or weak dispensing. It's a direct-replacement kit designed for compatible GE refrigerators. What it does

• Replaces a worn, cracked or clogged water inlet/fill tube to restore proper water flow to the dispenser or ice maker.
• Helps stop visible leaks or drips from the dispenser area caused by damaged tubing.
• Can resolve weak or intermittent water dispensing when the tubing is the source of the restriction.
• Works as part of the refrigerator's water pathway between the valve and dispenser/ice components.

• Turn off water supply and unplug the refrigerator before starting service.
• Inspect surrounding fittings and seals; replace any damaged clips or gaskets to ensure a watertight connection.
• Use basic hand tools; avoid overtightening plastic fittings to prevent cracking.

This wire shelf assembly replaces a damaged or missing freezer shelf to restore stable storage and organization. Durable coated wires hold frozen food off the floor of the compartment and maintain proper airflow when installed. What it does:

• Provides a stable, vented surface for storing frozen items
• Restores proper spacing and airflow inside the freezer compartment
• Replaces bent, broken, or rusted shelves that allow items to fall through
• Helps eliminate rattling or shifting caused by a warped shelf

• Disconnect power to the appliance before beginning any repair
• Remove food and any loose shelves or drawers to access the mounting area
• Use basic hand tools to release and seat the shelf into its mounting brackets; avoid forcing clips
• Inspect mounting brackets for damage and replace if the shelf does not seat securely

This is a bottom door hinge screw that secures the lower hinge assembly to the appliance door, restoring proper alignment and stable door movement. Use it to replace stripped, missing, or damaged hinge hardware. What it does

• Secures the bottom hinge to the door and helps keep the door aligned and level.
• Restores smooth, consistent opening and closing when a worn or missing screw causes sagging or misalignment.
• Prevents further wear to hinge components by maintaining correct hinge positioning.
• Works with original hinge assemblies; use the correct screw to avoid loose or unstable doors.

• Disconnect power to the appliance before performing any door or hinge repairs.
• Support the door while removing/installing the hinge screw to prevent the door from falling or causing injury.
• Use the correct screwdriver or bit to avoid stripping the screw head.
• Replace any additional worn hinge hardware as needed for proper alignment.

This replacement link actuator controls the freezer linkage assembly to restore proper door/damper movement and component alignment. It's a direct-fit OEM-design part for affected GE refrigerators, helping stop sticking or misaligned freezer linkages. What it does:

• Engages the freezer linkage to move the damper/door linkage as intended
• Restores smooth movement when a frozen or stiff linkage causes binding
• Helps correct intermittent operation or noisy linkage movement
• Prevents further wear by replacing a worn or broken actuator

• One link actuator

• Disconnect power to the appliance before starting work
• Basic hand tools are typically required; remove any panels blocking access
• Handle the actuator and linkage gently to avoid damaging plastic gears or tabs
• Verify proper operation after installation; do not force parts into place