Band Parts

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This small metal ring clip secures wiring and small assemblies in place to prevent movement and wear. It restores proper retention so harnesses and parts stop rubbing, rattling, or coming loose. What it does:

• Locks a wire, tube, or small component into its mounting position to prevent chafing or disconnection
• Helps stop intermittent electrical contact or noise caused by loose wiring
• Reduces vibration-related wear on nearby parts and connectors
• Commonly used where a compact, spring-style retention is needed

• One ring clip

• Turn off and unplug the appliance before inspecting or replacing clips
• Remove panels or trim per the manufacturer's service instructions to access the clip location
• Use needle-nose pliers to compress or expand the clip as needed; avoid bending it out of shape
• Replace any damaged clips—do not reuse if deformed or fatigued

This replacement part is a dryer clip, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This dryer clip is typically found on dryers and there are usually multiple clips on one appliance. These clips help hold the front panel in place and secure so that it does not come off during the drying cycle. A new dryer clip might be needed if the front panel of the dryer is off balance or not attached correctly. It is possible that the clips can become loose over time as the appliance is prone to shaking and vibrating. The clips are important as it keeps the dangerous parts covered. If the entire front panel can be lifted off then it is time to replace the dryer clips. These clips are sold individually even though dryers typically have more than one. This clip is a genuine OEM part.

A spring-style drain hose clamp that secures flexible drain tubing to fittings to prevent leaks and hose separation. Durable metal construction keeps drain connections tight for reliable wastewater flow and trouble-free operation. What it does:

• Holds drain hose firmly to pump, elbow or spud to reduce leaks and disconnections
• Applies even compressive force around flexible tubing for a secure seal
• Helps stop water spraying or pooling caused by a loose hose connection
• Commonly used on appliance drain and discharge lines where a snug clamp is required

• One spring-style drain hose clamp

• Use pliers to expand the clamp, fit over the hose, then release to engage; avoid twisting the hose while seating
• Replace any cracked or brittle hose before clamping to ensure a leak-free repair
• Disconnect power and water if required by your appliance before accessing the drain connection

This pressure hose clamp secures the small vacuum/pressure hose to its fitting, keeping the hose in place so the appliance can accurately sense water level and cycle pressure. Simple, direct replacement for a worn or loose clamp. What it does:

• Holds the pressure/vacuum hose snugly to prevent leaks or hose detachment
• Helps maintain proper pressure signal for correct cycle and fill operation
• Commonly used when a loose or damaged clamp causes intermittent pressure-related symptoms
• Small replacement part that restores a firm hose connection

• Disconnect power (and water, if applicable) before servicing the appliance
• Use a small screwdriver or pliers to remove the old clamp and secure the new clamp in place
• Ensure the hose is fully seated on the fitting before tightening the clamp

This inlet pipe clamp secures the refrigerator water inlet line to the cabinet or valve, preventing movement and wear. Replaces a worn or broken clamp to help stop chafing and reduce the chance of leaks. What it does:

• Holds the water inlet pipe or tube firmly in place to prevent rubbing and stress at connections
• Helps maintain a steady water line position for proper water/ice dispensing
• Prevents pipe vibration or movement that can lead to leaks or line damage
• Commonly replaced when the original clamp is cracked, loose, or missing

• One inlet pipe clamp

• Turn off water supply and unplug the appliance before starting work
• Access may require removing a small panel or the toe grille depending on model
• Remove the old clamp and snap or fasten the new clamp in the same location; use appropriate fastener if required
• Inspect tubing and connections for damage while replacing the clamp

To use with BOOT #wh8x246

This is a drain tube clip that secures the refrigerator/freezer drain tube to the cabinet, keeping the tube in place to help prevent water from pooling or dripping where it shouldn't. What it does:

• Holds the drain/defrost tube firmly against the cabinet or evaporator housing
• Helps prevent the drain tube from pulling loose and creating leaks or water buildup
• Reduces risk of ice forming from redirected or trapped meltwater around the evaporator area
• Simple mechanical retainer—no seals or gaskets included

• One drain tube clip/retainer

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Remove any access panels or shelving as needed to access the drain tube area
• Snap the clip over the drain tube and into the mounting boss or slot until it seats securely; use pliers if needed
• Inspect the drain tube for damage or clogs while installing; replace tube if cracked or deteriorated

This small plastic grille clip secures the appliance's lower/front grille or trim panel, keeping it aligned and preventing rattles or gaps. It restores a snug fit after a broken or missing clip. What it does:

• Clips the grille or trim to the appliance frame to hold panels securely
• Prevents grille vibration, rattling or sagging caused by a loose or broken clip
• Restores proper alignment so the grille sits flush with surrounding trim
• Works as a direct replacement for a worn, cracked or missing grille retainer

• One grille clip (single plastic retainer)

• Unplug the appliance or shut off power before accessing the grille area
• Remove the grille or access panel per the appliance manual to reach clip locations
• Press the new clip into the slot until it snaps; replace panel and confirm secure fit
• If other clips are damaged, replace all affected retainers for a uniform, secure fit

This water tube fastener secures the refrigerator's water tube/line to the cabinet or chassis, keeping the tubing routed and stable to prevent kinks and inconsistent water flow. Simple replacement helps restore proper line routing and reduces vibration noise. What it does:

• Holds the water inlet/dispenser tube in place to prevent movement and rubbing
• Keeps tubing routed away from sharp edges and hot components
• Helps prevent kinks that can restrict water flow to the dispenser/ice maker
• Reduces vibration-related noise from loose tubing

• Disconnect power and shut off the water supply before replacing any water-line hardware.
• Remove any access panels needed to reach the existing clip; use hand tools to unclip or remove fastener.
• Check for leaks and secure routing after installation.

This clamp assembly secures the washer's door boot (gasket) in its groove to maintain a watertight seal at the front of the tub. Replace a stretched, bent, or broken ring to stop leaks and keep the boot properly seated.

• Holds the door boot/gasket firmly to prevent front-panel water leaks
• Restores proper tension when the original ring is deformed or the spring fails
• Common symptoms: water leaking at the front, boot slipping off, visible broken or missing clamp
• Often replaced during door boot service to ensure an even, reliable seal

• Disconnect power and turn off water supply before servicing
• Carefully relieve tension and remove the old clamp without tearing the boot
• Install the new clamp evenly around the opening
• Run a short test cycle and check for leaks after reassembly