Starter Switch Parts

This micro switch is a small electromechanical door/control switch that restores reliable on/off signaling for your appliance. Replacing a failed switch helps restore normal operation and safety interlocks. What it does:

• Opens or closes an electrical circuit when actuated, enabling controls or motors to run
• Commonly used in door and safety interlock applications to prevent operation when open
• Can stop intermittent power or control-response problems caused by a worn switch
• Helps resolve symptoms like appliance not starting, controls not responding, or cycling unexpectedly

• One micro switch

• Disconnect power (unplug appliance or flip the breaker) before servicing
• Observe sharp edges and wear protective gloves; remove access panels as needed
• Verify correct switch orientation and actuator engagement before reassembly
• Test continuity with a multimeter after installation to ensure proper operation

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

For switch mounting nut, order part# WP422617.

This main wire harness routes power and control signals between the appliance's control board and components to restore electrical connectivity and reliable operation. Replacing a damaged harness helps eliminate intermittent faults and lost functions. What it does:

• Provides the primary electrical connections between the control board and motors, switches, sensors and valves
• Carries power and signal wiring so controls and components operate as intended
• Commonly replaces harnesses with broken, melted, or corroded wires or connectors
• Can resolve symptoms such as no power to components, intermittent operation, or unresponsive controls

• Disconnect power to the appliance before inspecting or replacing the harness
• Compare connector types and routing to the original harness; install in the same path to avoid chafing
• Secure connectors fully until they click; avoid pulling on individual wires
• If wiring or connectors show heat damage or corrosion beyond the harness, inspect associated components.

This pressure switch monitors the water level inside the washer tub and signals the control board when the correct fill level has been reached. It connects to a small air hose that runs to the tub. Replace this switch if your washer overfills, underfills, does not fill at all, or fails to advance past the fill cycle.

Oven light switch.

Fixes unresponsive fan controls and restores proper ventilation. This fan switch replacement typically takes 30-45 minutes with basic tools.

Microwave not heating? A failed high voltage transformer disrupts the voltage supply needed for heating. This repair requires electrical knowledge.

If your washer won't start or stops mid-cycle, this lid switch assembly detects lid closure to restore safety interlock. DIY-friendly, installs in 15 minutes.

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

Refrigerator won't start or stops running? A failed capacitor disrupts motor circuits. This film radial capacitor restores voltage stability and operation.

Freezer won't cool or makes clicking/humming sounds? This compressor start relay restores reliable motor startup. Simple DIY fix in under 30 minutes.

Refrigerator not cooling or running constantly? The power relay controls compressor startup. Direct fix for cooling failures in bottom-mount models.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

If your range burner won't spark or ignite when you turn the knob, this burner igniter switch restores spark delivery for reliable lighting.