Tape Parts

The door gasket is an OEM part for Whirlpool refrigerators. It forms a seal between the refrigerator door and body, working to ensure peak cooling and energy efficiency. This rubber gasket acts as insulation, preventing warm air from entering the refrigerator compartment each time the door is opened.

Causes of a bad door gasket can include cracks, tears, or compression from repeatedly opening and closing the refrigerator door over an extended period of time.

Symptoms of a bad door gasket include:

• Inefficient cooling and higher energy costs
• Warm air leaking into the refrigerator
• Moisture buildup or frost inside the body
• Difficulty properly sealing the door shut

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door gasket creates a tight seal around the refrigerator door to keep cold air in and humid room air out. Replacing a worn gasket helps maintain proper temperatures and reduces condensation and frost at the door opening. What it does:

• Seals the door perimeter to limit warm air infiltration
• Helps keep interior temperatures stable for consistent cooling
• Reduces moisture and frost buildup near the door opening
• Replaces a gasket that is torn, warped, brittle, or won't seal properly

• 1 door gasket

• Disconnect power before servicing
• Remove the old gasket from the retaining channel; on some models, loosen retainer screws to release it
• Warm the new gasket in hot water or with low heat to relax folds; seat corners first, then press fully into the channel all around
• Close the door to check for even contact; adjust door alignment if needed and allow up to 24 hours for the gasket to conform

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn seal helps stop warm air leaks, reduce frost and condensation, and keep temperatures stable for better efficiency and food preservation.

• Creates a continuous perimeter seal between the door and cabinet to prevent air infiltration
• Helps maintain correct temperatures and reduce moisture/frost buildup
• Restores proper door closing when the old gasket is torn, warped, or permanently compressed
• Common symptoms: door not sealing or popping open, condensation around the door, temperature swings, frost along the door edges

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Let the new gasket relax at room temperature or warm it in water to remove kinks
• Pull the old gasket from the door channel; clean the mating surface
• Seat corners first, then press the gasket fully into the channel; use gentle low heat to smooth waves if needed

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the refrigerator door opening to maintain cool interior temperatures during use.

Causes relate to the breakdown of sealing materials from repeated compression cycles over many years. Cracks or loose areas compromise the barrier.

Symptoms of a defective door gasket can include:

• Warm air entering around the door edges
• Interior humidity increases causing frost or condensation
• Higher electric bills from lost cooling efficiency
• Inability to maintain set temperatures over long periods

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Color - Grey

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

Seals the appliance door to prevent leaks and keep the interior working as intended. Replace a cracked, torn, or hardened gasket to stop leaks, reduce odor and mold, and restore a reliable door seal. What it does:

• Forms a tight seal between the door and cabinet to prevent water, air, or heat loss
• Stops common symptoms like visible cracks or gaps, water pooling, and persistent odors
• Restores proper containment for cleaning, heating, or washing cycles
• Matches the OEM channel/retainer design for a secure fit

• Disconnect power and water before beginning any repair
• Remove the old gasket, thoroughly clean the mounting area, then seat the new gasket into the door channel or retainer
• Work the gasket evenly around the door; avoid overstretching and ensure all beads/clips are fully engaged

This 27" oven door gasket seals the gap between the door and oven body to help maintain proper cavity temperature and reduce heat loss during cooking. It restores a tighter door seal for more consistent baking and roasting. What it does:

• Replaces worn or torn door seal that lets oven heat escape
• Helps the oven reach and maintain set temperatures more reliably
• Reduces hot spots and uneven cooking caused by a failing seal
• Minimizes heat transfer to surrounding cabinetry and reduces energy loss

• One door gasket (27")

• Disconnect power and allow the appliance to cool completely before starting
• Remove the old gasket and any adhesive or fasteners before installing the new gasket
• Press the new gasket into the door channel evenly, ensuring proper orientation and a continuous seal

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

This rear pan gasket seals the refrigerator crisper/condensate pan area to help prevent leaks and keep airflow directed where it belongs. It restores a tight seal to reduce moisture buildup and improve cabinet protection. What it does:

• Replaces a worn or cracked rear pan gasket to stop water from leaking under the pan
• Helps direct condensate and airflow properly to prevent excess moisture in the compartment
• Reduces the chance of food moisture issues or puddling under the pan area
• Fits the rear pan section, restoring the original sealing surface

• Designed for direct replacement; inspect mating surfaces and clean before installation
• Remove power to the appliance before attempting service and work with care around sharp sheet metal
• If adhesive is used on your model, use the OEM-recommended adhesive or clips as required

This replacement door seal restores the fridge door's airtight closure to help maintain proper cooling and reduce energy loss. Designed to fit original-style openings, it keeps cold air in and warm air out for reliable food preservation. What it does:

• Creates an airtight seal along the refrigerator door edge to maintain consistent interior temperatures
• Helps prevent frost buildup and reduces strain on the compressor by improving efficiency
• Addresses common symptoms like warm spots near the door, excess frost, or a door that won't close snugly
• Fits into the door channel and compresses when the door is closed to form a tight barrier

• Replacement may require door removal and trim manipulation; follow your model's service instructions
• Inspect the door channel and mounting flange for damage or debris before installing the new seal
• Warm the seal slightly to ease installation and ensure a uniform fit; avoid open flames or excessive heat
• Test the door for a consistent seal after installation and make any hinge/strike adjustments if needed

This adhesive seal tape is a replacement sealing strip used to restore a tight seal on appliance doors and panels, helping reduce air leaks and improve temperature control. It's a simple repair for worn or damaged seal edges. What it does:

• Provides a flexible, adhesive sealing surface to close gaps between door/panel and cabinet
• Helps reduce air or moisture leakage that can cause temperature loss or inefficient operation
• Restores worn or deteriorated sealing surfaces without replacing the entire gasket
• Compatible with applications where a narrow adhesive sealing strip is required

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the tape to fit; press firmly along the full length to ensure contact
• Allow adhesive to set per ambient conditions before closing the door or returning to service

The Refrigerator Front Leg Seal Cover is an essential component designed to maintain the stability and efficiency of your Samsung refrigerator. This genuine OEM part ensures a perfect fit, replacing the original seal cover with ease and restoring your appliance to optimal condition. Crafted from durable materials, the seal cover effectively protects the front legs of your refrigerator from dirt, moisture, and everyday wear, extending the lifespan of your appliance. Its precise design not only enhances the overall appearance of your refrigerator but also contributes to better energy efficiency by ensuring a tight seal. Installing the Refrigerator Front Leg Seal Cover is simple and straightforward, allowing you to quickly address any damage or wear without the need for professional assistance. Compatible with a wide range of Samsung refrigerator models, this seal cover provides reliable performance and peace of mind. Enhance the functionality and look of your refrigerator with this high-quality, genuine OEM part, ensuring your appliance remains sturdy and efficient for years to come.

This door gasket seals the oven door to help keep heat and cooking moisture inside for more even baking and efficient operation. It replaces a damaged or worn seal to restore a snug, continuous closure. What it does

• Provides a heat-resistant seal around the oven door to reduce heat loss
• Helps prevent hot air and steam from leaking during cooking
• Can reduce uneven baking or longer cook times caused by gaps
• Visible signs of failure include cracks, flattening, or gaps around the door edge

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Remove the old gasket by pulling from the retention channel; press the new gasket into the same channel until fully seated.
• Check the seal all the way around the door and make minor adjustments for an even fit.

This gasket seals the heating element opening to help maintain proper heat and prevent leaks or debris entry. It restores a tight fit between the element and the appliance cavity for safer, more efficient operation. What it does:

• Creates a heat-resistant seal around the heating element to reduce heat loss
• Helps prevent dust, grease, and moisture from entering the element cavity
• Reduces risk of shorting or arcing caused by gaps or damaged insulation
• Common symptom fix: frayed, cracked, or missing gasket around element flange

• One heating element gasket

• Disconnect power (or unplug) and allow the appliance to fully cool before servicing
• Access the element per your model's service instructions; remove element mounting hardware to replace gasket if required
• Inspect element flange and mounting surface; replace gasket only if it matches OEM shape and seating
• If you see corrosion, burning, or element damage, replace the element as needed and retest after installation