Starter Switch Parts

Fix dishwasher buttons that won't respond or cycles that won't start with this push button switch. Direct replacement for worn control panel buttons.

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

Fix a clicking fridge that won't cool with this compressor overload protector. Protects motor from overheating damage. Simple 10-15 minute DIY repair.

Refrigerator not cooling or running constantly? The power relay controls compressor startup. Direct fix for cooling failures in bottom-mount models.

Fix a refrigerator light that stays on or won't turn off when the door closes with a new door switch. Simple repair that restores proper door detection.

Compressor won't start or runs intermittently? This start relay and overload helps the motor get up to speed so your refrigerator runs reliably again.

If your washer overfills or underfills, the water level pressure switch may have failed. This switch senses water height and signals the control.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

This high-voltage transformer supplies the ignition voltage used to create sparks for gas burner/oven ignition. Replaces a worn or failed transformer to restore reliable spark firing and consistent burner ignition. What it does:

• Converts line voltage to the high-voltage pulse needed for spark ignition
• Sends ignition sparks to surface burners or oven igniters so gas will light
• Common symptom: clicking with no visible spark at the burner or burner(s) that fail to ignite
• Other symptom: intermittent ignition or weak sparking

• One high-voltage transformer

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the transformer and high-voltage leads with care; do not operate with covers removed
• Verify correct diagnosis before replacing; check ignition module, wiring, and spark electrodes for faults

This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. It replaces a failed relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Supplies the compressor's start winding with a timed boost to initiate motor start
• Helps prevent repeated clicking or humming when the compressor struggles to start
• Commonly used when the refrigerator is warm, not cooling, or the compressor does not run
• Works with the compressor start circuit as a replacement electrical relay

• Disconnect power to the appliance before accessing the compressor or electrical components
• Replace the relay on the compressor terminal block; ensure firm, correct terminal seating
• Inspect the compressor and start capacitor for related faults while servicing

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

Compressor won't start or runs hot? This overload protector stops your refrigerator compressor from overheating and prevents premature failure.