Hardware Hand Small Engine Flywheel Key Parts

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

Fix a loose refrigerator bin or drawer with this latch. Secures bins to mounting points, preventing spills and drops. Easy DIY replacement.

Secures burner or oven control to the control panel behind the knob. Replace if stripped, missing, or loose to keep control shaft stable and aligned.

Cooktop mounting screw secures the cooktop to frame or brackets. Replace if stripped, missing, or rusty to eliminate wobble, rattling, or lifted corners.

Shaft that the idler pulley rotates on in your dryer. Replace if worn, wobbling, or causing squealing. Helps maintain proper belt tension and alignment.

Door lock secures the appliance door during use, allowing cycles to start and run safely. Replace a broken or failing lock to restore proper closure and prevent interruption of operation. What it does:

• Latches and holds the door closed so the appliance can start and complete cycles.
• Triggers the control to allow operation only when the door is fully closed.
• Common symptom: appliance won't start or stops mid-cycle because the door won't latch.
• May be needed if the door feels loose, won't stay closed, or you hear clicking when trying to start.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle parts carefully; avoid forcing or bending mounting tabs during installation.
• Verify proper alignment and engagement of the latch before restoring power.

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.

Secures the oven door handle in place. Replace if screw is stripped, missing, or no longer holding the handle firmly against the door surface.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

Size: 8-18 x 1/2 inch.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Secures the handle to your dryer or microwave door panel. Replace this self-tapping screw if missing, stripped, or damaged to restore a firm grip.

Mounting hardware kit for securing your microwave during installation. Includes brackets and fasteners needed when original components are missing or damaged.