Hardware Hand Small Engine Spark Plug Parts
Genuine Ge part
By: Ge
Part Number: WD12X24637
Detergent not dispensing or dishwasher door won't close? This dispenser module releases detergent at the right time. Moderate DIY repair difficulty.
Do-It-Yourself Stories from Customers like You
Replace broken detergent module on a 6 month old GE dishwasher Timothy A. • Akron , IA • September 29, 2020
Watched you tube video, fixed with no problem.
Read more
More
$76.95
- Compare At:
-
$90.80
- You Save:
-
$13.85
Out Of Stock
Usually ships within 4 - 14 days
Genuine Bosch part
By: Bosch
Part Number: 00188978
Used to hold down the jet holder assembly.
Do-It-Yourself Stories from Customers like You
Left rear variable simmer gas burner on thermador prg364glus stopped working David B. • Lincoln , NE • February 23, 2017
First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you...
Read more
More
$15.71
- Compare At:
-
$18.69
- You Save:
-
$2.98
Out Of Stock
Usually ships within 4 - 14 days
Genuine Bosch part
By: Bosch
Part Number: 00263088
Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.
Do-It-Yourself Stories from Customers like You
Dispenser no longer opened Douglas L. • Fountain Hills , AZ • April 22, 2014
Removed back of dishwasher with hex screw driver 5 min
Unplugged power cord 30 secs
Loosened metal bracket on top and bottom with screwdriver 5 min
Pushed dispenser in and removed from dishwasher 5 min
Positioned new unit in space and snapped into place 1 min
Plugged electrics back in 1 min
Screwed back on 3 min
Roughly 20 min. I am nontechnical and rarely do repairs.
Read more
More
$210.39
- Compare At:
-
$248.26
- You Save:
-
$37.87
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB01X45506
This rivet assembly is a direct-replacement fastening piece used to secure appliance panels and components, restoring a stable, rattle-free fit and preventing movement caused by worn or broken rivets. What it does:
- Secures panels, brackets, or component mounts to restore proper alignment and support
- Stops rattling, vibration, or loose hardware caused by damaged or missing rivets
- Provides a durable mechanical fastener where original rivets have sheared or loosened
- Helps maintain safe operation by keeping parts properly retained
What's included: One rivet assembly Install notes:
- Disconnect power (and gas/water if applicable) before attempting any repairs
- Removal may require drilling out the old rivet; installation typically needs a rivet gun or equivalent tool
- Keep hardware orientation the same as the original; replace any damaged surrounding parts
Do-It-Yourself Stories from Customers like You
Ge microwave: sparking melted hole in stirrer fan cover and it would not run without sparking Henry H. • Swanton , OH • September 10, 2016
I replaced the stirrer fan cover and fan, which had some carbon and slight burn marks on it. It was difficult to remove the fan cover as it did not rotate. I had to pry it off with a flat blade screwdriver, breaking the plastic tabs on the cover (which was being discarded anyway). I then cleaned any visible carbon deposits and replaced the cover and fan, using the old stirrer fan holder as it appeared OK. However, I was unable to rotate the cover into the locked position so I could not insert...
Read more
More
$7.52
- Compare At:
-
$8.36
- You Save:
-
$0.84
Out Of Stock
Usually ships within 4 - 14 days