Lint Screen Parts

This lint filter traps lint and fibers as air moves through the dryer, helping maintain proper airflow and drying performance. Replace a damaged or missing screen to reduce lint buildup inside the machine and along the vent.

• Captures lint and debris during the drying cycle to protect the blower and venting
• Helps maintain airflow for consistent drying results and temperature control
• Reduces lint redepositing on clothes and around the door opening
• Replace if the mesh is torn, the frame is warped/cracked, or if you notice longer dry times or excess lint inside the drum

• Disconnect power before servicing
• Remove the old screen and vacuum out the lint chute/housing; inspect and clean the exhaust vent as needed
• Insert the new filter and ensure it seats fully and flush—do not operate the dryer without the filter in place
• Run a short test cycle to confirm proper airflow at the exhaust

This EMI line filter reduces electrical interference on the incoming power to help protect the appliance's electronics and ensure stable operation. A failed filter can leave the unit dead, intermittently power-cycling, or tripping a breaker.

• Filters electromagnetic interference (EMI) on the AC line
• Helps protect the control board and other sensitive circuits
• Common symptoms: no power, intermittent power, or breaker/fuse trips when the unit starts
• Typically located near the power-cord entry or main control

• Disconnect power before servicing; allow a few minutes for any capacitors to discharge
• Note and label wire positions; move wires one at a time to the new filter
• Secure the filter to its mounting bracket and ensure the ground connection is tight
• Inspect wiring for shorts or damage before restoring power and testing

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

This drain pump filter traps lint, coins, and small debris before they reach the pump, helping your washer drain properly and protecting the pump from damage. Replace a broken or clogged filter if you notice slow draining or a leak at the filter access.

• Screens out debris before it reaches the drain pump
• Helps maintain proper draining performance
• Common symptoms of a failed or missing filter: not draining/slow drain, leak at the filter access, or pump noise from debris
• Prevents hard objects from entering the pump and causing damage

• Disconnect power and turn off water before servicing
• Expect residual water; place towels or a shallow pan under the filter area
• Access the filter, unscrew and remove the old filter, and clear any debris from the housing
• Install the new filter and hand-tighten to seal; run a short drain cycle and check for leaks

This dryer lint filter, also called a lint screen, captures lint and debris from the exhaust air stream. Replacing a damaged or missing screen helps restore proper airflow, improve drying consistency, and protect the blower and vent.

• Traps lint and fibers from tumbling laundry to keep them out of the blower and vent
• Helps maintain proper airflow for consistent drying performance
• Aids in preventing lint buildup inside the dryer and exhaust duct
• Typical failure symptoms: torn mesh, cracked/warped frame, lint on clothes, longer dry times

• Disconnect power; for gas dryers, turn off gas supply
• Remove the old filter and vacuum lint from the housing/duct opening
• Insert the new filter fully in the correct orientation; never operate the dryer without the filter installed
• Run a brief test cycle to ensure proper fit and airflow

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This lint filter assembly traps lint and fibers from the exhaust airstream to maintain proper airflow and drying performance. Replace a torn or missing screen to help restore efficiency and reduce lint buildup inside the appliance and vent. What it does:

• Screens lint and debris from air leaving the drum
• Helps maintain airflow for consistent drying
• Helps keep lint out of the blower and vent path
• Common signs it's time to replace: torn mesh, cracked/warped frame, poor fit, excessive lint beyond the filter, longer dry times

• 1 lint filter assembly

• Disconnect power before service and allow the unit to cool
• Remove the old filter; vacuum/clean the lint housing and chute
• Insert the new filter fully and ensure it seats and moves smoothly
• Do not operate the appliance without the filter installed

This replacement lint filter fits in the dryer's lint trap to catch lint and fibers from each load. Replacing a torn or warped screen helps maintain airflow, improves drying performance, and keeps lint from circulating back onto clothes.

• Traps lint and debris drawn through the lint trap during drying
• Helps maintain proper airflow and protect the blower and vent path
• Replace if the mesh is torn, the frame is cracked/warped, or it won't stay seated
• Common symptoms: longer dry times, excessive lint on clothing or in the drum, difficulty inserting/removing the filter

• Disconnect power to the dryer before servicing
• Lift out the old filter and vacuum lint from the chute and surrounding area
• Install the new filter fully seated and flush in the opening; do not run the dryer without a filter
• Clean the lint screen before each cycle; check external venting if dry times remain long

The Filter is an OEM part for Whirlpool dryers. This lint filter catches loose fluff and lint before it escapes outside and helps prevent blockages in the vent ductwork. 

Causes of a clogged dryer filter involve normal buildup during frequent drying cycles over extended use. Signs of failure include:

• Drying times taking too long as airflow is impeded
• The dryer failing to properly sense airflow for thermal protection
• Strange noises or vibrations from restricted ventilation

Symptoms of a dirty filter consist of:

• Reduced air movement through vents and out of the dryer
• Red eyes, sinus issues or respiratory irritation from lint recirculating
• Clumps of fluff visible clinging within exhaust hoods and ducts

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replace a torn or warped lint screen with this lint screen assembly. It captures lint and debris from the dryer's airflow to help maintain ventilation, protect the blower, and support consistent drying performance.

• Traps lint and fibers as air exits the drum, preventing buildup in the blower and vent path
• Supports proper airflow for efficient, safe drying
• Replace if the mesh is torn, the frame is cracked/warped, or the handle is broken
• Common symptoms include longer dry times, lint on laundry or around the door, or the filter not sitting flush

• Disconnect power before servicing the appliance
• Open the door, slide out the old screen, and seat the new screen fully in the housing
• Clean the lint chute and vent opening while the screen is out to restore airflow
• Do not operate the dryer without a lint screen installed

The Filter is an OEM part for Frigidaire washing machines. This part traps debris, lint, and small objects that get washed out from clothes during the wash cycle. By filtering out these materials, the pump filter protects the drain pump and hose from clogs and potential damage, ensuring that the washing machine operates efficiently and the drainage system remains clear.

Causes of a bad washer pump filter can range from accumulation of lint and debris, which can clog the filter, to damage or wear that compromises its ability to filter properly.  

Symptoms of a bad filter include:

• The washing machine not draining properly or leaving clothes excessively wet
• Unusual noises from the pump area, indicating struggling or blockage
• Frequent pauses or stops during the drain cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This light gray lint filter cover shields the dryer's lint screen opening and helps direct airflow for efficient lint capture. Replace a cracked or missing cover to maintain airflow and reduce the chance of fabric snags.

• Covers the lint screen opening and channels air through the filter
• Helps keep the lint screen aligned and properly seated
• Provides a smooth edge at the door opening to protect fabrics
• Typical signs it's failing: cracks, broken tabs, loose lint screen, lint in drum, longer dry times

• Disconnect power before servicing
• Open the door; remove screws or release locking tabs to remove the old cover
• Position the new cover and secure it with existing hardware as applicable
• The lint screen slides in fully and seats flush before use

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This Whirlpool Lint Screen is an OEM part for specific Whirlpool dryer models. This lint screen is essential for trapping lint and debris from clothes during the drying process, helping to prevent duct clogs and maintain efficient dryer operation. 

Lint screens can become less effective or damaged over time due to lint build-up, wear, or accidental tearing. A compromised lint screen can lead to reduced dryer efficiency, longer drying times, and increased risk of lint-related safety hazards.

Symptoms of a bad lint screen include:

• Visible tears or holes in the lint screen.
• Excessive lint accumulation on clothes after drying.
• The dryer takes longer than usual to dry clothes.
• Reduced airflow in the dryer, is noticeable during operation.
• Increased lint build-up inside the dryer duct.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

Color: white. Measures about 10-1/2 inches wide by 13-1/2 inches deep.

Color: Gray. Measures about 16 inches wide by 7 inches high.