Tco Parts

A replacement cycling thermostat that helps regulate dryer temperature and prevent overheating by cycling the heater on and off as needed. Restores temperature control for safer, more consistent drying. What it does

• Opens and closes to cycle the heating element, maintaining proper operating temperature.
• Helps prevent excessive heat build-up that can cause clothes damage or dryer shutdowns.
• Common fix for dryers that run too hot, have uneven drying, or won't maintain heat.
• Works with the dryer's existing temperature control system to stabilize cycles.

• One cycling thermostat

• Disconnect power before accessing or replacing the thermostat to avoid shock.
• This part mounts inside the dryer cabinet near the heating assembly.
• Handle the thermostat carefully and reconnect wires to the correct terminals.
• Test the dryer on a short cycle after install and monitor temperature; if symptoms persist, check other heating components.

This Thermostat L225 is a temperature limit thermostat that helps regulate heat and prevent overheating in the appliance. It restores proper temperature control so the unit runs safely and more reliably. What it does:

• Acts as a temperature-regulating limit switch to stop heating when limits are reached
• Prevents overheating by opening the circuit at excessive temperatures
• Common symptom: appliance heating inconsistently or cutting out during cycles
• Can be checked for continuity when diagnosing heating problems

• Always disconnect power to the appliance before starting any repair
• Handle and install the part in the same orientation and mounting as the original
• Verify electrical connections are secure and use a multimeter to test continuity
• If other safety devices (thermal fuses/thermistors) failed, inspect and replace as needed per OEM guidance

This thermal fuse stops power if an appliance overheats, helping prevent damage and unsafe operation. Use as a direct replacement when the original high-limit fuse has failed and the appliance will not operate normally. What it does:

• Opens the circuit when temperatures exceed safe limits, acting as a high-limit safety cutoff.
• Protects the appliance and home from overheating-related damage and hazards.
• Common symptoms of a blown thermal fuse: appliance won't heat, intermittent heating, or the unit fails to start.
• If the fuse blows, it often indicates an underlying issue—inspect heating elements, thermostats, and venting for faults.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Allow the appliance to cool, then access the fuse location; note wiring orientation and terminal connections for reassembly.
• Replace with the exact type of thermal fuse; do not bypass, jumper, or defeat the device.
• If the replacement fuse fails again, check for restricted venting, failed heating components, or faulty thermostats/controls.

This NTC thermistor is a refrigerator temperature sensor that monitors cooling system temperature and helps the control board maintain proper operation. It replaces a failed sensor to restore accurate temperature sensing and reliable cycle control. What it does:

• Measures internal temperature and sends a changing resistance signal to the control board
• Helps the fridge adjust compressor/fan cycles for stable cooling
• Common symptom fix: erratic or incorrect temperatures, frequent cycling, or temperature-related error codes
• Works as the sensor used in evaporator/air temperature sensing circuits (model-dependent)

• One NTC thermistor sensor (wiring and connector as shown)

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring gently; avoid kinking or stretching the lead wires
• Mount and route the sensor per the unit's service diagram so it contacts the intended location
• Verify sensor response with a multimeter (NTC resistance should change with temperature) or follow the manufacturer's service procedure

High limit thermostat, Canadian models only.

This thermistor assembly senses appliance temperature and sends readings to the control board so the unit can regulate cooling. Replaces a failed or intermittent sensor to restore accurate temperature monitoring. What it does:

• Measures internal temperature and provides variable resistance feedback to the control board.
• Helps the control system maintain desired cooling by reporting temperature changes.
• A faulty thermistor can cause temperature fluctuations, poor cooling, or incorrect temperature readouts.
• Can clear temperature-related error codes when replaced as directed by diagnostics.

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle the sensor and wiring gently; avoid pulling on wires or connectors.
• Install in the original sensor location and route wiring as OEM to prevent interference or damage.

This mechanical temperature control thermostat regulates refrigerator temperature to keep food cold and cycling the compressor as needed. Replaces a faulty control to restore proper cooling performance and temperature stability. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to maintain set temperature.
• Stops the compressor when the refrigerator reaches the selected temperature and restarts it as needed.
• Commonly replaced when the fridge runs continuously, won't reach set temperature, or has erratic cooling cycles.
• May produce a clicking sound when switching or fail to make electrical contact, causing cooling loss.

• Disconnect power to the appliance before starting any repair.
• Access may require removing interior panels or control housing; keep track of fasteners and wire locations.
• Verify wiring and operation with a multimeter; replace only with the correct OEM part.

This heater thermistor is a temperature-sensing replacement part that helps the appliance monitor and regulate heating. Replacing a failed thermistor restores accurate temperature feedback for safer, more consistent operation. What it does

• Measures temperature near the heater and sends a signal to the control board.
• Helps the unit cycle heating on and off to maintain proper operating temperature.
• Common symptom: appliance won't heat or heats intermittently.
• Common symptom: cycles too frequently or shows error codes related to temperature sensing.

• One heater thermistor.

• Disconnect power before accessing or replacing the thermistor.
• Handle the sensor and connector carefully to avoid damage to the lead or plug.
• Verify connector orientation and secure wiring; do not force connectors.

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed