Jet Clean Parts

The Frigidaire Refrigerator Water Filter Cover is an OEM part for Frigidaire refrigerators. It serves as a protective casing for the water filter, ensuring it is shielded from damage and securely in place within the appliance. This cover helps maintain the aesthetic integrity of the interior of your refrigerator while also providing easy access for filter changes.

Causes of a bad water filter cover can include physical damage such as cracks or breaks, which may occur from accidental impacts or during the filter replacement process.  

Symptoms of a bad Water Filter Cover include:

• Difficulty in accessing or replacing the water filter
• Loose fit that can lead to vibration or noise
• Visible damage like cracks or warping

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This filter reduces contaminants and removes chlorine taste and odor to provide cleaner, fresher water. The coconut carbon activated filtration media removes microscopic particles down to 0.5 microns. Compatible with select GE side-by-side and bottom-freezer refrigerators. Simple twist and lock design provides easy, tool-free, no-mess filter replacement. For best filtration results, filter cartridge should be replaced every six months or 300 gallons. Filter Media: Coconut Carbon Block. Micron Rating: 0.5. Filter Type: Canister. Flow Rate: 0.5 gpm. Approximate dimensions: 5 x 3.5 x 3.5 inches. Temp. Range: 33 - 100 °F. Press. Range: 30 - 120 PSI. Meets NSF Standard: 42. Approved for WQA Gold Seal. This part replaces the MWF filter.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Medium LP orifice

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

This LP conversion kit reconfigures a compatible gas appliance from natural gas to liquid propane. Using the manufacturer-specified setup helps ensure proper fuel flow, correct flame characteristics, and safe performance when operating on propane.

• Converts the appliance for propane service by setting gas pressure and burner fuel metering for LP
• Required when installing a natural-gas-configured unit in a location with propane supply
• Helps achieve proper flame size and color after switching fuel type
• Helps prevent poor combustion and soot related to an incorrect fuel setup

• Follow manufacturer instructions and local codes
• Disconnect electrical power and shut off the gas supply before beginning
• Adjust the gas pressure regulator for LP and change specified components as directed
• After conversion, leak-test all connections and verify burner operation and flame quality

Color: metallic. Measures about 11-1/2 inches wide by 12 inches deep.

Keep your fridge smelling fresh with this PureAir AF-1 refrigerator air filter. It reduces common food odors as air circulates through the compartment, helping maintain a cleaner, fresher interior when replaced at the interval your model recommends.

• Filters recirculating air in the fresh food compartment to reduce lingering odors
• Helps limit odor transfer between foods
• For refrigerators equipped with the PureAir AF-1 air filter housing
• Replace when the filter indicator prompts or when odors persist

• Locate the air filter housing inside the fresh food section; refer to your owner's manual for the exact location and orientation
• Open the cover, remove the used filter, and insert the new filter fully seated
• Close the cover and reset the air filter reminder/indicator, if your model has one
• If working near internal fans or wiring, disconnect power for safety

The Water Filter Housing and Tube Assembly is an OEM part for GE refrigerators. This assembly is responsible for securely holding the water filter in place while directing water through the filter and into the dispenser or ice maker. Approximate dimensions: 18" x 14.7" x 3.3"

Over time, the water filter housing and tube assembly can become damaged due to regular use, exposure to high water pressure, or mineral deposits building up inside the tubes. Such damage may lead to leaks or reduced water flow, affecting the performance of the refrigerator's water and ice systems.

Symptoms of a faulty water filter housing and tube assembly include:

• Water leaks around the filter area
• Low water flow to the dispenser or ice maker
• Difficulty installing or removing the water filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

For 9.5k burner.

This rear orifice holder mounts beneath the cooktop to route gas from the valve to the rear surface burner. It positions the orifice correctly for reliable ignition and a stable, even flame at the rear burner.

• Channels gas from the valve through the orifice to the rear surface burner
• Aligns and supports the orifice spud for proper flame shape and height
• Helps address delayed ignition, weak/uneven or yellow flames at the rear burner
• A damaged or loose holder can contribute to clicking without lighting or a gas odor near the burner

• Shut off gas supply and power; allow the cooktop to cool before servicing
• Remove grates, burner caps/heads, and lift or release the cooktop to access the manifold area
• Detach the old holder from the valve and mounting points; note orientation and transfer the existing orifice spud to the new holder
• Reassemble, restore gas, and check all connections for leaks with a soapy-water solution; verify proper ignition and flame

This surface burner orifice meters gas to the right-front burner, helping maintain the correct flame size for even, reliable cooking performance. Replace if the original is clogged, damaged, or mismatched to restore proper burner operation. What it does:

• Regulates gas flow to the right-front surface burner
• Helps maintain correct flame size and shape for consistent heating
• Can help resolve weak/uneven flame or a burner that struggles to light or stay lit
• Replaces a clogged, damaged, or incorrect orifice during repair

• Turn off gas supply and power; allow the cooktop to cool
• Remove grate, cap, and burner head to access the orifice in the orifice holder
• Use the correct driver; thread carefully and do not overtighten the brass orifice
• Restore gas and check all connections for leaks with a soap-and-water solution; verify proper flame

Water filter head and tubing assembly holds the water filter and connects the water lines to the water filter. Approximate dimensions: 13.6" x 12.7" x 4.6"

The Ignitor/Orifice Assembly is an OEM part for Frigidaire ranges and ovens. This assembly includes the ignitor and the orifice, both essential for the proper operation of gas burners. The ignitor provides the initial spark to ignite the gas, while the orifice regulates the precise flow of gas to the burner.

Causes of a bad ignitor/orifice assembly include:

• Ignitor wear leading to weakened or failed sparks
• Clogged or obstructed orifice restricting gas flow
• Physical damage or corrosion to the assembly components

Symptoms of a faulty ignitor/orifice assembly include:

• Failure to ignite the gas burner
• Uneven or irregular flame patterns
• Potential gas odors or safety hazards

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The orifice spud is the fixed jet that meters gas to a burner. Replacing a worn, clogged, or incorrect spud helps restore proper flame size, cleaner combustion, and reliable ignition on your gas cooking appliance.

• Precisely meters gas flow to the burner through a fixed opening
• Helps produce a stable blue flame and consistent heat
• If clogged, damaged, or wrong size, can cause weak/yellow flames, uneven heating, delayed ignition, or burners not lighting
• Supports correct operation when matched to the specified fuel type and burner rating

• Shut off gas supply and power before servicing
• Match the spud to the exact burner position and fuel type specified in your model documentation
• Thread the spud into the orifice holder/manifold with a wrench; do not overtighten
• Restore gas, then leak-test connections and verify proper flame characteristics

Liquid propane