Jet Clean Parts

This replacement housing serves as the structural cover/mount for a specific appliance assembly. Replacing a cracked or damaged housing restores secure mounting and protection so components stay aligned and operate as intended. What it does:

• Holds and positions the related components for correct operation
• Shields internal parts and wiring from impact and vibration
• Restores proper fit when the original housing is cracked, warped, or broken
• Common symptoms include loose/misaligned parts, rattling noises, broken tabs, or visible damage in the affected area

• 1 housing

• Disconnect power; if the serviced area ties into water, shut off the water supply
• Wear cut-resistant gloves; edges and surrounding sheet metal can be sharp
• Transfer any sensors, seals, or hardware from the old housing to the new one
• Reuse existing screws/clips; align carefully and do not overtighten, then test operation

This LP orifice spud meters gas to a range burner when using liquid propane. Replacing a worn or incorrect jet helps restore proper flame size and clean combustion during LP setup or conversion.

• Meters LP gas to the burner for correct flame height and color
• Helps resolve large yellow flames, soot, and poor simmering caused by an incorrect/blocked spud
• Supports safe operation when converting from natural gas to LP per the manufacturer's instructions
• Can improve ignition and flame stability when the original jet is damaged or clogged

• Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
• Remove the existing spud with the correct wrench and install the replacement snugly—do not overtighten
• Perform any required air-shutter/burner adjustments per the service instructions
• After installation, leak-check with a soapy water solution; LP conversions should comply with local codes

This is an orifice holder, sometimes referred to as a surface burner orifice holder. This part allows the gas to reach the burner so that the stove works for cooking on the stovetop. This part is compatible only with gas ranges.The user will need to replace this part if the orifice holder is bent, broken, or missing. It's possible the holder is damaged if the gas is not consistent or if the gas will not turn on at all. Always make sure to turn off the gas supply and double check that the oven is completely off before starting this repair. The user will need some tools for this repair including a screwdriver, a mounting screw, and sealing putty to make sure there is an airtight fit. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from manufacturers like General Electric.

This refrigerator water filter housing secures the filter cartridge and channels water through the system. Replacing a cracked or leaking housing helps restore proper water flow and leak-free dispensing and ice production.

• Holds and seals the water filter; connects the inlet and outlet water lines
• Routes filtered water to the dispenser and ice maker
• Common failure signs include leaks at the filter area, slow/no dispensing, or no ice production
• A worn housing can prevent the filter from seating or staying locked in place

• Unplug the refrigerator and shut off the water supply before starting.
• Dispense water to relieve line pressure; keep a towel handy for residual water.
• Note tube orientation; transfer any brackets or fittings from the old housing as needed. Ensure tubing is fully seated and locked.
• Restore water and power, then check for leaks and flush the system per the filter instructions.

Color: metallic. Measures about 13-1/2 inches wide by 5 inches high.

The Grease Filter is an OEM part for Bosch ranges and cooktops. It is responsible for capturing and containing grease, oils, and other vapors produced from cooking to help keep indoor air fresh and prevent buildup. Regular cleaning is important to maintain optimal performance.

Causes of a bad grease filter can include excess buildup that blocks airflow from frequent high-heat cooking. Exposure to flames or excessive heat may cause damage over time as well.

Symptoms of a bad grease filter include:

• Reduced suction power and airflow from the range hood
• Grease accumulation on surrounding surfaces below the hood
• Unpleasant cooking odors escaping into the kitchen rather than being vented outside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

This whole house carbon filter is used in water pumps to reduce the number of contaminants found in water. This filter removes odors, rust, sediment, and sand that is often found in well water and some city-provided water. These impurities can affect the taste of drinking water and, in turn, affect the taste of coffee, tea, and foods cooked using water. It may also have an odor if the area has a high concentration of sulfur or iron. The manufacturer suggests replacing the filter every 30,000 gallons or every three months. This carbon filter is used on an in-line water filter that supplies water for the whole house. It is often used in combination with water softeners. If the water begins to taste or smell before the filter's three-month recommended life, a new filter should be installed. If the water quality is bad, the filter may need to be changed more often than recommended. This is normally indicated by smell and taste in foods and beverages made with water. This whole house carbon filter is sold individually. It is an authentic OEM replacement part sourced directly from the manufacturer. It is designed for use in water filters manufactured by General Electric.

This Venturi is an OEM part for Bosch Ranges. It plays a role in supplying air to the burner for proper combustion. Continuous exposure to heat and debris can cause this part to degrade or malfunction.

What Causes a Bad Venturi: 
Exposure to heat and debris from cooking can cause the venturi to deteriorate over time. Blockages or clogs in the venturi can also affect its functionality.

Symptoms of a Bad Venturi:

• Uneven flame or inconsistent burner operation
• Reduced gas flow to the burner
• Burner flame discoloration

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement orifice spud for the cooktop surface burner threads into the orifice holder to meter gas flow, helping ensure proper flame size and reliable ignition for consistent cooking performance. What it does:

• Meters gas flow to the surface burner through a calibrated opening
• Helps produce stable, properly sized flames for even cooking
• Replace if the original spud is clogged, stripped, or damaged
• Common symptoms include weak/low or no flame, yellow/orange flames, uneven heating, or delayed ignition

• 1 orifice spud

• Turn off the gas supply and disconnect power; allow the appliance to cool completely
• Remove grates, burner caps, and burner heads to access the orifice holder
• Use the correct spud for the specific burner position and gas type per your model documentation
• Start threads by hand and tighten snugly without overtightening; after reassembly, check for leaks with a soapy-water solution and verify ignition and flame

Liquid propane. Simmer burner

Convert your compatible natural-gas range to run on propane with this LP conversion kit. It supplies the factory-matched components to meter LP correctly so burners ignite and perform as intended after a proper conversion.

• Converts select natural-gas ranges for LP operation per the model's instructions
• Helps achieve proper flame size and color after conversion
• Use when installing a range where propane is the fuel source
• Incorrect or unconverted setup may show oversized/yellow flames, soot, or poor simmer

• Shut off gas supply and electrical power; allow all burners to cool before service
• After conversion, set the pressure regulator to LP, verify burner flames, and leak-test all joints with a non-corrosive solution
• Retain removed natural-gas parts for possible future reconversion

This charcoal filter fits an over-the-range microwave hood and absorbs cooking odors when the unit is set to recirculate indoors. Replacing a saturated filter restores effective odor control and helps keep vent airflow unobstructed.

• Absorbs smoke and odors in non-vented/recirculating installations
• Helps maintain proper vent airflow and fan performance
• Common signs it's due: lingering odors, weak vent suction, dark/discolored filter media, or a damaged/crumbly filter
• Restores intended odor-reduction performance after the original filter is saturated

• Disconnect power to the microwave before servicing
• Remove the upper grille/access panel to access the charcoal filter compartment
• Slide out the old filter; install the new one in the same orientation and seat fully
• Reinstall the grille, restore power, and test the vent fan

The Range Left Panel Assembly Kit is designed to seamlessly replace and restore the left panel of your Samsung range. This genuine OEM part guarantees a perfect fit, ensuring that your appliance maintains its original functionality and appearance. Crafted from high-quality materials, the assembly kit provides durable support and enhances the structural integrity of your range. Installing the Range Left Panel Assembly Kit is straightforward, allowing you to quickly and easily fix any issues without the need for professional help. By choosing this genuine OEM part, you ensure compatibility with your Samsung range model, avoiding potential fit or performance problems associated with aftermarket alternatives. This assembly kit not only replaces damaged or missing panels but also preserves the sleek and professional look of your kitchen appliance. Whether youGÇÖre dealing with wear and tear or accidental damage, the Range Left Panel Assembly Kit offers a reliable solution to keep your Samsung range functioning smoothly and looking its best. Invest in this essential part to enhance the longevity and aesthetic of your range, providing you with a dependable cooking experience for years to come.

This water filter housing secures and seals the refrigerator's filter cartridge, routing water to the dispenser and ice maker. Replace it if the filter area leaks, the filter won't seat, or water/ice flow is reduced. What it does:

• Holds and seals the filter cartridge to the water system
• Directs water through the filter to the dispenser and ice maker
• Helps maintain proper pressure and a leak-resistant connection at the filter head
• Typical symptoms: leaking at the filter area, slow/no water from the dispenser, no ice production, filter won't lock in place

• 1 water filter housing assembly

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Note tube routing; use the quick-connect collets to release/insert water lines fully
• Restore water and power, check all connections for leaks, and flush the dispenser to clear air

The LP Conversion Kit is an OEM part for Whirlpool gas ranges. It allows the unit to be converted from natural gas operation to liquid propane use. Included in the kit are all necessary components for a safe and proper conversion such as LP orifices, regulator, and installation instructions.

Causes of needing this conversion kit include:

• Moving to a home that only has LP gas service instead of natural gas
• Switching fuel sources to utilize less costly liquid propane

Symptoms that it may be time for an LP conversion include:

• Inability to light burners or oven due to insufficient gas pressure
• Burners or oven not heating properly on liquid propane
• Gas pressure regulator delivering too much or too little fuel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This ignitor orifice assembly sits under the cooktop and both routes gas to a surface burner and provides the spark to light it. Replace a damaged or clogged assembly to restore fast, reliable ignition at that burner.

• Feeds gas from the valve to the burner and houses the spark igniter electrode for ignition
• Common fix for a surface burner that won't light, has no or weak spark, or only lights with a match
• Also called an igniter/orifice holder assembly

• Disconnect power and shut off the gas supply before servicing.
• Raise or lift the cooktop per your model's service information; support it to avoid strain on gas lines.
• Note wire routing; set the electrode gap to the burner head per service specs and keep the lead away from heat/sharp edges.
• After reassembly, check all gas connections with an approved leak-detection solution and verify proper spark and flame.